What specialist testing can show
TI-5000JX bench. Check Hall state sequence and tachometer independently on the scoped connection.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. TI-5719 on the documented 12-contact Souriau. Module TI-5105.
Bosch SD / SE 60° Hall and Tachometer Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| SD / SE 60° Hall and tachometer | TI-5719 with TI-5105 on the scoped branch. Match the exact connector and motor drawing. |
| Other Bosch feedback | Separate SF EnDat and SR digital resolver paths appear in the Mitchell index. Confirm the fitted motor. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Commutation | 60° Hall type as described by Mitchell for this connection. |
| Speed feedback | Tachometer circuit. Confirm its type, rating and polarity from the fitted documentation. |
| Fixture | TI-5719, 12-contact Souriau, with TI-5105. |
Interface and measuring method
Check the Hall sequence and tachometer response independently. Use the actual motor reference when interpreting sector sequence or a speed alarm.
Mounting and fit
Inspect the rear connector and harness before opening the housing. Obtain the matched Bosch drawing and record sensor and tachometer location.
Wiring and connector scope
Identify the Hall supply and outputs, tachometer conductors and shield from the exact fitted diagram. Match the Souriau mating view.
Internal motor and machine cables
Trace the motor pigtail and machine harness as separate parts. Record the connector key and cable exit before sourcing a replacement.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Drive trips on commutation | Check the documented Hall state sequence and phase reference. |
| Speed fault with Hall states present | Check tachometer wiring and response. |
| Both signals fail at the motor plug | Inspect retention and isolated continuity. |
Angle of alignment and commissioning
Capture the incoming motor phase reference, Hall direction and tachometer polarity. The cable index’s 60° designation identifies the Hall type. Use the motor-specific alignment procedure.
Motor and drive applications
Bosch SD/SE with documented 12-contact Souriau feedback
Identify the Hall type and tachometer wiring before applying a motor-specific alignment procedure.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer Support. Bosch Support Part Numbers, TI-5719 and TI-5105
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.