What specialist testing can show
TI-5000JX bench. Use the documented OBA/OSA17 selection after identifying the fitted HG-KN connector.
TI-3000JX motor run. Exact motor-run setup open.
Starting lead. Start with the Mitchell HG connector table. TI-5658 applies to its 9-pin Tyco branch.
Mitsubishi Electric HG-KN OBA/OSA17 Serial Motor Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| HG-KN | Motor family. Use the full nameplate order for frame, brake and connector details. The fitted encoder P/N is a separate label. |
| OBA/OSA17 | Mitchell’s bench selection for HG-KN and HG-SN. It identifies a test profile rather than a universal replacement part. |
| HG-MR / HG-SR and other HG-xR | Mitchell lists the OBA/OSA18 selection for several other HG variants. Check the complete suffix before testing. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| HG-KN resolution | The HG-KN/HG-SN manual states 17 bits, 131,072 position increments per motor revolution for the documented combinations. |
| Drive mode | Mitsubishi distinguishes absolute/incremental capability with specified MR-JE-B/C models and incremental operation with MR-JE-A. Check the exact drive suffix. |
| Feedback transport | Mitchell describes a two-wire serial data branch for newer HG connections. Use the HG-KN motor and connector drawing. |
Interface and measuring method
The amplifier reads serial position. The count format and receiver mode depend on the installed drive. A controller description of incremental operation does not identify separate ABZ wires at the motor.
Mounting and fit
Match the motor frame, rear connector arrangement and brake option. The HG-KN manual provides dimension drawings by motor order. Identify the fitted encoder seat, shaft and connector before applying service settings.
Wiring and connector scope
Use chapter 3 of the Mitsubishi HG-KN/HG-SN motor manual for connector configuration A. Mitchell lists TI-5658 for the 9-contact Tyco branch of its HG connection table. Confirm that branch against the actual connector and pin view.
Internal motor and machine cables
Mitsubishi lists TE 2174053-1 for the configuration A mating connector and 1674339-1 for the motor encoder connector. Those are connector references. Obtain the exact OEM cable or internal assembly by full motor and drive order.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| No communications after a cable swap | Check the two-wire serial arrangement and connector view. Separate an incorrect test profile from a damaged data pair. |
| Position reads but the mode is wrong | Verify the MR-JE suffix, selected mode and reference state. Inspect the retained position setup where fitted. |
| Intermittent fault at the motor connector | Inspect the plug latch, pin seating and cable support. Test the isolated harness and compare it with the factory connector diagram. |
Angle of alignment and commissioning
Capture the original machine reference and drive settings before removing feedback. Verify the mechanical seat and direction after fitting. Use the matched Mitsubishi procedure for position or absolute-reference recovery.
Motor and drive applications
Mitsubishi HG-KN · MELSERVO J4
Check the connector and two-wire data pair before selecting a profile. Record the fitted feedback ID separately.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitsubishi HG Series Motors · Melservo J4. Series and Connection Types. HG-KN and HG-SN use the OBA/OSA17 selection.
- Mitsubishi HG-KN/HG-SN servo motor instructions. Manufacturer reference for the indicated motor or feedback option. Check the fitted revision.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.