What specialist testing can show
TI-5000JX bench. Compare the PCB label with ID readback. Service units can report a different configured type.
TI-3000JX motor run. Use the documented matching run selection only after identifying the actual motor and reported ID.
Starting lead. Match the fitted connector and serial wiring before selecting the cable.
Mitsubishi Electric OBA18 Built-In Serial Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| OBA18 | Built-in Mitsubishi serial feedback. Photograph the large IC marking and any PCB labels when they are safely accessible. |
| OSA18 | Removable Mitsubishi feedback assembly. Compare the fitted housing and shaft coupling before choosing a part. |
| Replacement programmed as another type | Use the original motor and the tester’s reported encoder ID to confirm the supported selection. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback | Mitsubishi serial family, named OSA/OBA18 in the Mitchell catalogue. |
| Construction | Built-in encoder on the motor shaft in the OBA identification branch. |
| Electrical and mechanical values | Use the actual motor, full encoder revision and connector drawing for supply, data, resolution and fit. |
Interface and measuring method
The receiver reads a serial response. The TI-5000JX encoder ID field helps separate an assembly marking from the configured type the drive sees.
Mounting and fit
Use the motor’s rear assembly procedure. Photograph the shaft or disk assembly and harness route before specialist work. Opening an OBA cover reveals components that can lose alignment if disturbed.
Wiring and connector scope
Use the actual Mitsubishi motor and drive drawings. Check the approved supply, return and serial paths by connector view. Record both fitted connector sides before assigning a Mitchell lead.
Internal motor and machine cables
Keep the motor’s internal board lead and the drive-to-motor cable as separate references. Check continuity only on an isolated, disconnected cable and compare to the actual wiring.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Board says OBA18 but the drive expects another type | Read the ID through the documented tester connection and compare with the original motor history. |
| Response drops under cable movement | Inspect the connector clamp and the isolated extension or internal lead. |
| Alarm starts after rear assembly work | Check the fitted disk, housing reference and approved motor procedure before powering it again. |
Angle of alignment and commissioning
Record motor order, reported encoder type, direction and original reference. Confirm the motor’s procedure before disturbing the disk, changing a programmed selection or enabling a motor run.
Motor and drive applications
Mitsubishi motor with confirmed OBA18 board and serial configuration
Identify the built-in assembly and configured ID before comparing it with a removable OSA18.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitchell Product Catalog, supported feedback. Mitsubishi supported feedback, OSA/OBA18 entry
- Mitsubishi Motors. Supplementary reference for the stated model or setup.
- Mitsubishi Motors and Serial Encoders. Reference for the fitted feedback or motor option.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.