What specialist testing can show
TI-5000JX bench. Compare the fitted label, incremental channels and the P-series commutation sequence.
TI-3000JX motor run. Verify the exact motor, poles, alignment and matching run configuration.
Starting lead. TI-5091 on Mitchell’s documented B/P Ono Sokki connection.
Reliance / ElectroCraft P21M0304G Ono Sokki Incremental Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| P21M0304G | Mitchell’s named P-series example. Verify the actual feedback maker, encoder ID and motor plug. |
| Ono Sokki or equivalent | Read the fitted part number to establish line count, output and mechanical fit. |
| B14H1060 | A different B-series example. Mitchell describes four poles for that example and six for the P-series example. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback method | Incremental motion with a separate commutation path on the documented P-series case. |
| Motor example | Six poles on the P21M0304G case described by Mitchell. |
| Diagnostic connection | TI-5091 on the applicable feedback connection. Confirm the pin view, encoder supply and complete part. |
Interface and measuring method
The controller counts incremental motion while it uses commutation information to determine motor phase. Good count activity does not establish that the commutation channels and phase reference are correct.
Mounting and fit
Record the fitted shaft, coupling or hub and encoder attachment before removal. Use the full P-series motor and encoder orders for the rear drawing and positioning references.
Wiring and connector scope
Use the P-series wiring and documented TI-5091 arrangement. Verify the plug, position channels, commutation and supply against the actual view. The same motor family can contain an equivalent encoder with a different internal lead.
Internal motor and machine cables
Trace the encoder-to-bulkhead harness and the machine cable independently. Identify the OEM harness from both ends. Verify cable strain at the encoder and at the external plug.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Counts change but the motor will not start correctly | Check the commutation path and received phase reference separately. |
| Wrong scaling after replacement | Compare the fitted encoder count and controller settings. |
| Fault follows cable movement | Check both the internal strain relief and the isolated machine cable before condemning the encoder. |
Angle of alignment and commissioning
Preserve the received commutation reference and verify the actual pole count. Use the specific P-series motor reference and correct phase convention before specialist alignment work.
Motor and drive applications
Reliance P series, documented P21M0304G example
Use the P-series order and commutation wiring to identify the fitted encoder and avoid applying the B-series setup.
Related SpareFaber guides
Drawings, pin maps and manuals
- Allen Bradley (Reliance, Electrocraft) Motors. B and P Series identification and Connection paragraphs
- Mitchell Test Cable Index by Manufacturer. Supplementary reference for the stated model or setup.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.