What specialist testing can show
TI-5000JX bench. Verify both the serial count and incremental outputs in the matching ABS-E profile.
TI-3000JX motor run. Mitchell directs the matching 2,048-count case to Sanyo selection 4. Confirm the fitted label, motor poles and complete setup before running.
Starting lead. TI-5013 on the documented connector.
Sanyo Denki E07B111335 ABS-E Serial and ABZ Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| E07B111335 | The bench text and chart show this exact number, an ABS-E profile and TI-5013. |
| E07B1113335 | Extra digit in the run article prose. Verify the fitted label and the 2,048-count run selection. |
| E07B151103 | Separate 32,768-count branch in the same manual. Use its own signal and lead scope. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Within-turn serial | 2,048 counts or 11 bits in Mitchell’s ABS-E documentation. |
| Turn field | Mitchell describes a 13-bit turn field for this legacy example. Retention depends on the fitted installation. |
| Incremental path | A and B with Z, listed separately from serial data in the supported-types chart. |
| Starting lead | TI-5013 on the documented 17-contact MS arrangement. |
Interface and measuring method
The serial path reports position and turn information. The separate incremental channels provide a movement signal and a reference. Test the paths independently before assigning a drive fault to the encoder.
Mounting and fit
Record the complete motor and encoder labels and the shaft coupling, seating features and rear connector orientation. The fitted assembly drawing is needed for dimensions and a replacement decision.
Wiring and connector scope
Use the Sanyo Denki supported-types and pin reference together with the TI-5013 drawing. Confirm the connector view, serial request/response path, incremental circuits and any battery path in the actual assembly.
Internal motor and machine cables
Identify the motor-to-drive harness separately from TI-5013. For the short encoder loom, map the full connector and PCB revision before ordering or building a replacement.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Serial data stable but index missing | Check the isolated Z circuit, coupling and index behavior using the approved breakout. |
| Incremental channels read and serial is silent | Check the correct ABS-E profile and serial circuits rather than replacing the encoder based on a single path. |
| Readout scale or run behavior inconsistent | Confirm the E07B111335 label and 2,048-count profile. The Sanyo run text uses a longer spelling. |
Angle of alignment and commissioning
Capture the incoming position and the incremental reference where available. Check the direction and OEM alignment procedure for the actual motor before commissioning.
Motor and drive applications
Legacy Sanyo Denki ABS-E motor applications
Resolve the part-number spelling on the label and isolate serial versus A/B/Z faults.
Related SpareFaber guides
Drawings, pin maps and manuals
- Sanyo Denki Motors and Serial Encoders. Types Supported, E07B111335 2,048-count row and identification paragraph
- Sanyo Denki Motors. Supplementary reference for the stated model or setup.
- Mitchell Sanyo Denki supported-types table. E07B111335 resolution, A/B/Z paths and TI-5013.
- Mitchell cable index. TI-5013 17-contact MS test lead.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.