What specialist testing can show
TI-5000JX bench. Verify the actual label and the supported-types table. The bench prose uses E07B171103 while the table and run example use E10B171103.
TI-3000JX motor run. Mitchell lists the E10B17 eight-pole profile for the 131,072-count example. Confirm the complete motor and installed selection.
Starting lead. TI-5056 on the listed E10B171103 motor connection.
Sanyo Denki E10B171103 17-Bit ABS-E Serial Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| E10B171103 | Encoder designation in Mitchell’s 61BM run example and supported feedback listing. |
| 61BM120BXAT0 | Exact eight-pole example. Other 61BM orders need their own pole count and setup. |
| E10B17, P8 C131072 L-++ | Mitchell’s run-selection text for this example. Its phase reference is scoped to that motor and tester procedure. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Within-turn count | 131,072 positions per revolution in the documented 17-bit selection. |
| Feedback | ABS-E serial with incremental A/B described in Mitchell’s bench material. |
| Exact motor setup | Eight poles and TI-5056 commonly used on the 61BM120BXAT0 example. |
Interface and measuring method
The documented motor starts and runs using serial position. Assess serial identity and position separately from any incremental tracks brought out by the fitted encoder. A usable incremental signal does not establish correct ABS-E communication.
Mounting and fit
Use the full 61BM order for the rear assembly and coupling drawing. Record the axial location, shaft position and original cable dressing before removal. Keep unidentified housing screws and the encoder mounting hardware separate.
Wiring and connector scope
Use the TI-5056 fixture and the matching Sanyo connector drawing. Verify the supply, return and serial pairs from the fitted plug view. Follow the approved retention procedure where the installed system uses a battery.
Internal motor and machine cables
Keep the short encoder-to-motor harness separate from the motor-to-drive cable. Record both connector views and the drive model to identify the OEM loom. TI-5056 is the Mitchell starting test lead.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Similar encoder selected and count looks wrong | Compare the fitted E10 label and the documented E10B17 profile. |
| A/B activity with a serial alarm | Check the serial path, approved supply and connector at the proper fixture. |
| Reference changed after encoder work | Compare the saved reference and exact pole count before commissioning. |
Angle of alignment and commissioning
Record the received reference. The TI-3000JX manual reports zero count for its documented −U/+V/+W lockup on 61BM120BXAT0. A specialist should use the full procedure and motor identification for any powered alignment verification.
Motor and drive applications
Sanyo Denki 61BM example
Resolve the spelling discrepancy against the label and use the exact 61BM test and reference example.
Related SpareFaber guides
Drawings, pin maps and manuals
- Sanyo Denki Motors. Types Supported and E10B17 run example for 61BM120BXAT0
- Sanyo Denki Motors and Serial Encoders. Supplementary reference for the stated model or setup.
- Mitchell supported feedback catalogue. Sanyo Denki list confirms the E10B171103 designation.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.