What specialist testing can show
TI-5000JX bench. Match the exact N8401 label and confirm the current SmartABS bench selection and data scope.
TI-3000JX motor run. Mitchell lists TS5700N8401 in Generic Tamagawa V3.1. Confirm motor and approved setup.
Starting lead. Verify the fitted N8401 connector, supply and retention wiring.
Tamagawa Seiki TS5700N8401 SmartABS Serial Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| TS5700N8401 | Exact model in the Mitchell run menu and Nidec SmartABS example. |
| TS5700N8400 | Nearby TS5700 suffix covered separately. Check the full order, plug, data and mechanics before any substitution. |
| Nidec SI-Encoder V2 | A documented receiver example. Match your actual drive and its software before applying the settings. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Serial format | Tamagawa SmartABS in the Nidec receiver example. |
| Position word | 23 bits for position within a turn and 16 bits for turns in that example. |
| Mitchell run setup | Generic Tamagawa entry requires the actual motor’s pole count, direction and electrical reference. |
Interface and measuring method
The receiver separates the within-turn field from the turn count. A drive can show a valid position within one revolution while the turn information is misconfigured or unavailable. Check both fields.
Mounting and fit
Use the exact TS5700N8401 drawing for the mounting seat and shaft engagement. Photograph the fitted label, plug and cable exit before removal. Confirm the motor OEM arrangement before using a drawing for a nearby suffix.
Wiring and connector scope
Use the exact encoder and drive diagrams to identify supply and serial data. Nidec’s SI-Encoder V2 example documents receiver setup. Confirm the encoder pin view and retention implementation for the actual assembly.
Internal motor and machine cables
Identify the internal and external harness by encoder suffix, motor and receiver. Record cable length, mating views and whether the cable is fixed or flexing. A Mitchell fixture must match the actual wiring.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Within-turn position works but turns are wrong | Check the drive’s SmartABS turn-bit setup and the fitted retention implementation. |
| No data on a similarly named encoder | Confirm N8401, the supported receiver and exact wiring before choosing a profile. |
| Motion or direction differs after fitment | Compare the saved motor reference and receiver configuration against the OEM procedure. |
Angle of alignment and commissioning
Record the original position, direction and motor reference. Mitchell’s Generic Tamagawa run method requires a verified pole count, direction and lockup reference for the fitted motor. A specialist should use the motor-specific procedure.
Motor and drive applications
Exact TS5700N8401 on a compatible SmartABS system
Use the exact N8401 designation, documented word format and retention path to choose the right profile.
Related SpareFaber guides
Drawings, pin maps and manuals
- Generic Tamagawa Feedback Selection. Generic Tamagawa V3.1 supported encoders, TS5700N8401
- Nidec Control Techniques SI-Encoder V2 User Guide. Supported devices and SmartABS N8401 preset with the two position fields.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.