What specialist testing can show
TI-5000JX bench. Use the OBE12 selection and check the 12-bit single-turn count and data wiring.
TI-3000JX motor run. Mitchell lists P8 OBE12. Confirm the fitted motor has that supported pole configuration.
Starting lead. TI-5027 on the documented OBE12 connection.
Mitsubishi Electric OBE12 12-Bit Serial Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| OBE12 | Mitchell lists 4,096 counts per turn and TI-5027 for the documented installation. |
| OBA13 | The nearby 13-bit Mitsubishi branch. Check its retention and connector against its own documentation. |
| OBE102 | A different encoder label. It has a separate guide and application scope. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Position | 12 bits and 4,096 counts per turn in Mitchell’s OBE12 row. |
| Retention circuit | Mitchell’s OBE12 description identifies a version without a battery line. Verify the actual harness before service. |
| Mechanical family | Mitchell describes OBA/OBE as built-in arrangements. Obtain the motor-specific installation drawing. |
| Run scope | P8 OBE12 in the Mitsubishi TI-3000JX list. |
Interface and measuring method
The receiver reads position through the serial connection. Verify the motor and encoder profile before comparing counts and status. An incompatible profile can give a false diagnostic result.
Mounting and fit
Record the encoder, motor and connector labels. Use the motor drawing to identify the built-in feedback carrier, locating features and shaft relationship before disassembly.
Wiring and connector scope
Confirm TI-5027 and the actual 9-contact AMP connection from the Mitchell index. Use the exact fitted drawing for supply, return and serial pairs. Identify the motor connector view separately.
Internal motor and machine cables
Use the complete motor and drive orders to identify the external cable and fitted internal harness. Verify each conductor with both ends isolated and retain the specified shield termination.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| 12-bit position scale appears incorrect | Confirm OBE12 and the actual reported encoder ID before changing the drive or tester configuration. |
| Serial communication absent | Verify the fitted TI-5027 connection, isolated cable and matching supply path. |
| Motion fault after reassembly | Inspect the carrier, locating reference and fitted loom before assigning the fault to the drive. |
Angle of alignment and commissioning
Record the original reference and drive settings before changing the built-in assembly. Check motor poles and the OEM alignment procedure after fitting.
Motor and drive applications
Legacy Mitsubishi OBE12-equipped motors
Read the short OBE12 marking correctly and identify the corresponding lead and run selection.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitsubishi Motors and Serial Encoders. Types Supported, OBE12 row and Mitsubishi encoder identification
- Mitsubishi Motors. Supplementary reference for the stated model or setup.
- Mitchell Mitsubishi encoder chart. OBE12 count and starting lead in the supported-types table.
- Mitchell cable index. TI-5027 9-contact AMP scope.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.