Identify the fitted part
| Guide scope | Allen-Bradley 1326AB S2L singleturn HIPERFACE — motor application |
|---|---|
| Feedback identity | SICK Stegmann HIPERFACE; exact fitted family to verify |
| Main model / application identifier | 1326AB S2L singleturn HIPERFACE |
| Motor order / source example | Retain every nameplate suffix; a family example is not a verified fitted motor order. |
| Interface | Classic HIPERFACE singleturn |
| Starting connection | TI-5064 at the documented motor boundary; direct 8-pin uses TI-5069 |
| Configuration distinction | TCG243 is M2L multiturn and TCG340 is resolver. S2L is the singleturn option. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX feedback scope. Identify S2L, preserve the stored alignment offset and verify feedback after refitting the retaining cover. TI-5104 only with correctly cabled, rating-compatible HIPERFACE fixture. Memory-derived offset, never a universal alignment angle. |
|---|---|
| Starting lead / fixture | TI-5064 at the documented motor boundary; direct 8-pin uses TI-5069 |
| Profile / module | TI-5104 only with correctly cabled, rating-compatible HIPERFACE fixture. Memory-derived offset, never a universal alignment angle. |
| TI-3000JX motor-run scope | Conditional motor-run setup: verify exact motor, fitted feedback, poles, wiring, alignment, lead/module and installed TI-3000JX profile before running. |
The documented test reference is Allen Bradley (Reliance, Electrocraft) Motors — MPS/MPL/MPF/1326AB overview and memory section; OEM feedback-code table. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current availability, discontinuation and a verified successor for the exact fitted order remain to confirm with the manufacturer. The linked technical documents establish a scoped reference, not stock or drop-in interchangeability. Compare motor, drive, mechanical fit, interface, loom and memory requirements before ordering.
Specifications and interface
| Feedback technology | Classic HIPERFACE singleturn |
|---|---|
| Position retention | Singleturn option: verify within-turn position; no multiturn function is inferred. |
| Memory | Motor identity and commutation-offset information must match the fitted motor. No common numerical alignment angle is assigned. |
| Exact fit and ratings | Use the matching manufacturer drawing for supply, connector view, shaft/coupling, dimensions and fastening. Unknown values remain open. |
Classic HIPERFACE carries serial position/identity data alongside analogue sine/cosine feedback. Evaluate both independently. A correct within-turn reading does not confirm multiturn retention, motor data or the analogue signal quality. Match the supply to the exact encoder and connection boundary; this scope does not include HIPERFACE DSL.
Mechanical fit and retention
Record the incoming shaft datum, locating seat, coupling, retaining cover, fasteners and cable exit before removal. After isolation, inspect accessible looseness, contamination, rubbing and bearing condition. Use the exact outline and service procedure for engagement, rear clearance and fastening. Preserve the original relationship; do not import a torque or air gap from a similar-looking motor. The 1326AB retaining cover can affect encoder body position; verify alignment after its final installation.
S2L identifies the 1326AB singleturn classic HIPERFACE configuration; M2L multiturn and resolver applications have separate guides. Mitchell notes that removing the rear cover can leave the encoder body free to move. An alignment result obtained with that cover removed therefore needs rechecking after final retention. The matching motor-side connection can permit this final check without reopening the assembly. The stored offset is specific to the motor.
Wiring and connector boundaries
Separate the encoder plug, internal motor loom, bulkhead, machine cable and tester fixture. Verify contact numbering, keying, gender and the drawing viewpoint. Identify supply/return, signal pairs, shield and any independent temperature or brake paths from the exact drawing. No unverified pin map is assigned in this guide.
Starting connection for this guide: TI-5064 at the documented motor boundary; direct 8-pin uses TI-5069. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
The exact fitted internal loom part number has not been verified. Record both ends and obtain the motor assembly drawing. Machine cable choice also depends on receiver, length, shield termination and fixed/flexing duty. A Mitchell test lead describes a bench connection and is not an OEM replacement cable number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact assembly | S2L identifies the 1326AB singleturn classic HIPERFACE configuration; M2L multiturn and resolver applications have separate guides. Mitchell notes that removing the rear cover can leave the encoder body free to move. An alignment result obtained with that cover removed therefore needs rechecking after final retention. The matching motor-side connection can permit this final check without reopening the assembly. The stored offset is specific to the motor. |
|---|---|
| Intermittent fault during cable motion | After isolation and disconnection at both ends, inspect flex points, pin engagement, moisture and repairs. Check continuity and unintended shorts against the exact diagram, accounting for intentional shield bonds. |
| No signal or communication | Confirm the encoder option, fixture and supply range. A qualified technician can compare source and load voltage using the approved breakout and manufacturer procedure. Connector shape alone is insufficient. |
| Position reads but the drive rejects feedback | Check independent signal paths, motor identity, direction and index/retention state. Record the original alarm and readable data before settings changes. A reset does not establish correct motor data. |
| Serial data reads but motion feedback is unstable | Measure analogue signal quality with the correct fixture and inspect shaft attachment and harness condition. Keep data-path and track-path findings separate. |
Alignment, reference and memory
Record the original mechanical reference, direction, motor phase convention, retained state and readable data before disturbing the feedback. Use the exact motor procedure for alignment and replacement. Electrical communication alone does not establish the machine origin or a correct motor/feedback pairing. Allen-Bradley memory carries motor-specific information. Recover the original data where supported, compare it with the motor plate and use the derived offset for that motor. The source’s example angles are not universal. Memory support and writing require the corresponding enabled motor option and compatible replacement.
Motor and drive applications
1326AB S2L singleturn HIPERFACE. TCG243 is M2L multiturn and TCG340 is resolver. S2L is the singleturn option.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Allen Bradley (Reliance, Electrocraft) Motors — MPS/MPL/MPF/1326AB overview and memory section; OEM feedback-code table
- Rockwell 2098-IN001: Ultra5000 installation — Family-specific motor code, dimensions and connection tables; match fitted revision
Obtain the complete fitted motor order, encoder label, internal loom drawing, connector contact view and approved fixture. Match the linked family document to the actual order and revision.
Common questions
What should accompany a 1326AB S2L singleturn HIPERFACE enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Conditional motor-run setup: verify exact motor, fitted feedback, poles, wiring, alignment, lead/module and installed TI-3000JX profile before running. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.