What specialist testing can show
TI-5000JX bench. Check serial ID and position on the matched DT EnDat connection.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. TI-5707 for the 12-contact M23 branch.
AMKmotion DYNASYN DT Heidenhain EnDat Servo Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| DYNASYN DT EnDat | Use the exact motor code to confirm the 12-contact M23 branch. |
| AMK E/F option examples | AMK documentation lists optical singleturn and multiturn EnDat 2.1 with sine/cosine for these codes. Verify the applicable table. |
| AMK P/Q option examples | Separate inductive EnDat 2.2 light options in the AMK documentation. Match the fitted connector. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Connection | TI-5707, 12-contact M23, for the scoped DT EnDat branch. |
| Feedback format | Singleturn or multiturn according to encoder and motor order. |
| Signal selection | Use the DT type key to check digital-only versus EnDat with analogue tracks. |
Interface and measuring method
A valid serial position confirms the digital path. Where the fitted configuration has analogue tracks, check those separately before replacing an encoder.
Mounting and fit
Use the actual DT frame and encoder documentation for rear location and attachment. Record the motor and encoder labels and original position.
Wiring and connector scope
Match the motor connector drawing to its feedback code. Identify supply, clock, data and any analogue pairs at the documented mating view.
Internal motor and machine cables
Record the production lead separately from TI-5707 and the short encoder connection. Trace an intermittent circuit with the harness isolated.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Position valid but analogue alarm | Confirm the feedback code and whether tracks are present. |
| No serial response after replacement | Verify the fitted EnDat option, supply and connector. |
| Unexpected turn range | Check singleturn or multiturn type and the original drive parameters. |
Angle of alignment and commissioning
Save the original reference and motor setup where supported. Verify direction, turn format and encoder location through the applicable AMK commissioning procedure.
Motor and drive applications
AMK DT with the documented 12-contact M23 feedback option
Separate this EnDat build from other DYNASYN DT feedback and connector options.
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer Support. EnDat/AMK DT row, TI-5707
- AMKmotion DYNASYN DD/DT motor operating documentation. Supplementary reference for the stated model or setup.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.