What specialist testing can show
TI-5000JX bench. Check the matched encoder’s serial ID and turn data. Verify its separate analogue signal path.
TI-3000JX motor run. Confirm the actual AM3 drive, connection and the supported HIPERFACE run profile.
Starting lead. TI-5094 direct to the fitted SKM connection documented by Mitchell.
Beckhoff AM3000 / AM3500 SKM Multiturn HIPERFACE Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| AM3000 / AM3500 with SKM | Multiturn HIPERFACE. The cited AM3000 type key lists SKM under feedback option 8. Verify the applicable revision. |
| AM3 with SKS | Singleturn companion in the type table. |
| AM3 BiSS or EnDat | Separate serial feedback branches with their own motor-side setup. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Position format | Multiturn absolute on the scoped SKM option. |
| Signal path | Analogue motion tracks with a serial channel on the fitted HIPERFACE device. |
| Bench access | Mitchell lists TI-5094 for direct SKS/SKM access. Match the connector and verify module selection. |
Interface and measuring method
Check serial identification and position separately from the sine and cosine tracks. A valid direct reading helps narrow the fault to the internal loom, bulkhead or drive side.
Mounting and fit
Read the AM3 frame and full SICK order. Use the matching motor and encoder drawings for rear mount, restraint and coupling or taper.
Wiring and connector scope
Trace the direct encoder connection and the motor bulkhead as separate pin views. Match supply, analogue and serial circuits from the fitted drawing.
Internal motor and machine cables
Record the internal SKM cable and the machine extension part numbers. Check lock and strain relief before replacing the encoder.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Direct test good, drive feedback absent | Trace the internal loom and motor bulkhead. |
| Serial position reads but movement alarm | Check analogue pairs and fitted feedback selection. |
| New turn field or offset after replacement | Compare SKM versus SKS, original data and reference. |
Angle of alignment and commissioning
Capture original turns, direction and motor reference where supported. Use the complete motor and drive setup to verify retained data and reference after replacement.
Motor and drive applications
Beckhoff AM3 with the scoped SKM multiturn option
Choose the SKM branch by type key and separate an encoder fault from an AM3 harness fault.
Related SpareFaber guides
Drawings, pin maps and manuals
- Beckhoff AM Series Motors. AM2/AM3 direct SKS/SKM entry. Beckhoff AM3000/AM3500 type key, SKM multiturn option.
- Beckhoff AM3000/AM3500 operating instructions. Supplementary reference for the stated model or setup.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.