Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
An approved low-voltage fixture with the documented pull-ups can check 500 cycles/rev, quadrature, index and repeatability through a known turn. Inspect the connector and hub before using a different receiver. Exact Mitchell support remains unverified.
Broadcom HEDS-5540#A11 Optical Incremental Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is HEDS-5540#A11. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| HEDS-5540#A11 | Standard housing, 4 mm motor shaft hub. Align the base and hub per Broadcom. | 500 CPR, A/B quadrature plus index, 5 V nominal. |
| HEDS-5540#A05 | 3/16 in shaft hub, per ordering key. Same family mounting concept. | 500 CPR and index. Check shaft fit before choosing this code. |
| HEDS-5500#A06 | 1/4 in shaft hub, per ordering key. | Two-channel series. The pin used for index on HEDS-5540 is unused on HEDS-5500. |
Production and end-of-life status
DigiKey identifies the exact A11 code as active in its product record. Confirm Broadcom production and lead time for the exact code before sourcing.
Specifications
| Parameter | Value and scope |
|---|---|
| Order code | HEDS-5540 three-channel optical encoder. A specifies 500 CPR and 11 specifies a 4 mm shaft. |
| Supply | 4.5–5.5 V DC at recommended conditions. Ripple under 100 mV peak-to-peak. |
| Signal | A, B and index I. 2.7 kΩ pull-ups per Broadcom Figure 1. One TTL load per output as shown. |
| Count frequency | 100 kHz guaranteed under the documented conditions. Check the speed and assembly tolerances for the application. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Use the HEDS-5540 three-channel assembly sequence in AV02-1046EN. Align the base using the specified locating pins or HEDS-8910 alignment tool as applicable. Use the 4 mm hub on its specified shaft projection and ensure access for the hub screw. Check for rubbing or damage before power-up. Use the datasheet's set screw instruction and tool size for this assembly.
Interface and measuring method
A transmissive optical codewheel interrupts light as the shaft turns. The electronics generate A and B quadrature plus one index per turn. The receiver reconstructs relative movement by counting, and uses index to establish reference. The output circuit requires the specified pull-ups.
Verified wiring
Use the pin-1 marking on the HEDS-5540 body and Figure 1 or Figure 5. This is the five-contact three-channel version.
| Pin | Signal |
|---|---|
| 1 | GND |
| 2 | Index I |
| 3 | Channel A |
| 4 | +5 V nominal |
| 5 | Channel B |
The datasheet shows 2.7 kΩ pull-ups to +5 V at the outputs. Verify the actual receiver loading and pin numbering before power is applied.
Cables inside the motor and at the machine
Broadcom lists HEDS-8903 for the three-channel five-wire lead and gives Molex 0050579405 and 0016020097 for the single-ended cable connector hardware. HEDS-8902 is the two-channel lead and lacks the index conductor. Check the actual harness and the equipment-side connector independently.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| No pulses or a low logic level | Verify supply, return and the required pull-ups. Confirm the hub rotates without contact. |
| Counts intermittent after remounting | Check hub fit, base centering, shaft play and any evidence of codewheel damage. |
| A/B present, index absent | Check pin 2 and the HEDS-8903 conductor, then test the index output under the documented load. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use on compact motor or machine assemblies with a compatible 5 V TTL incremental receiver and correct shaft. Keep the installation clean and protected as required. The exact motor and controller determine any further setup.
Angle of alignment and commissioning
The HEDS-8910 procedure aligns the encoder to the motor shaft. The machine establishes its own index-based origin and direction. For motor commutation, follow the equipment manufacturer's procedure for that motor and feedback option.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Recommended operating conditions and pull-ups. Use the three-channel circuit, including Figure 1.
- Mounting and assembly. Shows the alignment tool and hub procedure.
- Mating lead and connector. Figure 5 shows the HEDS-8903.
- Ordering information. Decodes the A11 options.
- Exact A11 product record. Distributor corroborates the order code and configuration.