What specialist testing can show
TI-5000JX bench. Check motion and index with the verified feedback cable and receiver.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. TI-5673 on the documented 12-contact M23.
DIETZ DV Series Baumer ABZ Incremental Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| DV Series with Baumer ABZ | Scope of TI-5673. Verify the fitted motor and encoder labels. |
| DIETZ/Global DB9 | A different connection also named in Mitchell’s DIETZ cable entries. Verify actual hardware. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback | Incremental A/B and reference Z on the named DV branch. |
| Connector | 12-contact M23 test path. |
| Fitted output | Read the exact Baumer label for supply, receiver and line count. |
Interface and measuring method
Use A/B movement and direction and the reference Z to distinguish a missing channel from a mounting or cable problem. Match the actual encoder output type to the controller.
Mounting and fit
Record the shaft or hub, restraint and cable route. Obtain the fitted Baumer and motor drawings before disturbing the assembly.
Wiring and connector scope
Match the correct M23 pin view and supply to the original drawing. Check signal returns and shield after verifying isolation and disconnecting the cable ends.
Internal motor and machine cables
Identify the motor pigtail and drive extension separately. Check contact retention and strain relief. The cable index gives the starting test connection.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Motion counts lost | Verify fitted supply and A/B paths. |
| Index absent | Check Z and the drive’s reference selection. |
| Fault follows cable flex | Inspect the M23 contacts and disconnected harness. |
Angle of alignment and commissioning
Capture direction and index position at a known mechanical point. Use the fitted OEM procedure to restore the reference after replacing feedback.
Motor and drive applications
DIETZ DV with documented 12-contact M23 Baumer feedback
Identify the Baumer M23 version of DV and distinguish it from the other DIETZ connector branch.
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer Support. DIETZ and Baumer Support Part Numbers, TI-5673
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.