What specialist testing can show
TI-5000JX bench. Verify the EnDat 2.2 selection, supply and fitted connector before a TI-5000JX serial check. Mitchell’s article documents direct and motor-side branches with different requirements.
TI-3000JX motor run. Confirm the exact motor order, amplifier, fixture and commissioning data before a run test.
Starting lead. Family leads TI-5668 for the stated EnDat 2.1 direct branch and TI-5662 for the stated 8-contact M12 branch. Exact 550111 fixture open.
Festo EMMS-AS-55-M-LS-TM HEIDENHAIN EQI 1130 EnDat Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| EMMS-AS-55-M-LS-TM · 550111 | Festo’s exact size-55 multiturn motor order. Mitchell links this motor as an EQI 1130 example. |
| HEIDENHAIN EQI 1130 | Encoder family named for that example. The complete HEIDENHAIN ID and connector revision come from the fitted encoder. |
| 550110 · EMMS-AS-55-M-LS-TS | Separate singleturn motor order in the Festo catalogue. |
| 1569788 · EMMS-AS-55-M-LS-RR | Resolver order for this size and motor family. Use its own connection drawing. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Motor encoder interface | EnDat 2.2 for Festo item 550111 in its exact product datasheet. |
| Measurement | Inductive absolute multiturn. The 550111 datasheet lists 19-bit encoder resolution. |
| Motor size | Nominal 55 flange size in the Festo series catalogue. Use the size-55 outline for mounting and shaft dimensions. |
Interface and measuring method
The drive requests position over the EnDat clock and data lines. Mitchell says the documented EMMS-AS serial arrangements do not use the incremental outputs. A line-level test intended for analogue incremental channels does not diagnose the serial path.
Mounting and fit
Use the Festo size-55 motor outline for the flange, pilot and output shaft. The EQI 1130 sits inside the motor and needs the exact encoder drawing for its own seating, coupling and fasteners. Capture its installed clocking and cable routing before disturbance.
Wiring and connector scope
Separate the motor plug and the connector on the EQI 1130. Use the actual Festo connector table and fitted HEIDENHAIN drawing for supply, return, clock and data. Mitchell’s TI-5668 note names an EnDat 2.1 direct branch, while the exact Festo datasheet lists EnDat 2.2. Confirm the lead and software against this encoder before connecting.
Internal motor and machine cables
Select Festo’s external encoder lead from the catalogue by drive and actual motor plug. Mitchell’s generic EnDat direct lead and its M12 motor lead are separate fixtures. Source the internal EQI harness from the fitted connector and motor assembly documentation.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| No analogue signal on the tester | Check the serial EnDat path and response first. This application uses serial feedback. |
| No serial response | Verify the fitted EnDat generation, tester profile and direct-versus-bulkhead lead. Trace the isolated clock and data pairs and check connector seating. |
| Position reads but the drive trips after replacement | Verify the fitted ID, commissioning data, coupling and reference. Read the drive alarm before altering memory. |
Angle of alignment and commissioning
Read and preserve the original commissioning record and any accessible encoder memory. Record the mechanical and electrical reference before removal. Recommission using the Festo motor and drive procedure and verify position and multiturn behavior before handing back the axis.
Motor and drive applications
Festo EMMS-AS, size 55, exact motor order EMMS-AS-55-M-LS-TM
Confirm the fitted HEIDENHAIN ID, EnDat 2.2 fixture and internal loom identifier.
Related SpareFaber guides
Drawings, pin maps and manuals
- Festo EMME-AS, EMMS-AS and EMMT-AS Series. EMMS-AS, linked EQI 1130 motor example
- Festo item 550111 technical datasheet. Exact motor and its EnDat 2.2 and encoder resolution data.
- Festo EMMS-AS catalogue and dimension drawings. Motor type key, flange and shaft outlines, connector assignments and cable accessories.
- Festo manufacturer item 550111. Exact motor order and manufacturer data downloads.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.