Site visit or send-in evaluation
We can trace the EnDat link and analog tracks separately, then inspect the rotor fit and stator coupling if the fault points to the encoder assembly. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell documents direct testing of EQN 1125 with TI-5668. On an approved TI-5000JX setup, establish the supported EnDat profile and verify the 1 Vpp input path separately. A bench read can distinguish data or analog track faults from a faulty drive harness.
A TI-3000JX run needs the exact MOOG motor, drive-independent run selection and lead arrangement. Verify those before energizing a motor.
HEIDENHAIN EQN 1125 678096-20 EnDat01 Multiturn Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is 678096-20. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| 678096-20 | EQN 1125, shaft 27E and coupling 28D. Blind Ø6 mm bore with axial retention. Recessed stator mounting face, Ø43 mm bolt circle. | EnDat01, 15-pin double-row axial PCB connector, D533387. 512 lines of separate ~1 Vpp signals. |
| EQN 1135 | Related 1100-series family. Compare the actual shaft and coupling code. | EnDat22 family. Confirm drive and harness compatibility. |
| EQN 1325 827039-04 | Larger frame and a different shaft/coupling arrangement. | Related multiturn EnDat01 unit with different PCB connection. Compare the separate EQN 1325 guide. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Absolute position | 8,192 positions per turn and 4,096 distinguishable turns, binary |
| Incremental track | 512 periods per turn, ~1 Vpp. −3 dB cutoff frequency 190 kHz. |
| Power at the encoder | 3.6 to 14 V DC per HEIDENHAIN's record for 678096-20 |
| Motor-side mechanical codes | 27E shaft, 28D stator coupling, Ø43 mm coupling bolt circle |
| Connection | 15-pin straight double-row PCB connector, axial outlet, D533387 |
| Operating temperature | −40 °C to +115 °C for the reference ID. Verify the motor's thermal limit as a separate specification. |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
The Ø6 mm blind bore centres the rotor on the motor journal. Axial retention fixes the encoder rotor to the motor shaft. The recessed-face stator coupling holds the encoder housing against rotation while allowing the specified mounting compliance.
Confirm the motor shaft engagement length, the offset between the mounting and shaft faces, and cable clearance. Use the 27E/28D drawing and motor assembly procedure to check the central fastener and coupling attachment. Obtain the specified fasteners and torque before tightening.
Interface and measuring method
The drive clocks the EnDat01 data path to read an absolute turn and position. Separate differential sine/cosine tracks carry fine incremental motion between the absolute reads. A drive may read an absolute position while reporting an analog amplitude or tracking error. Treat each path as a separate diagnostic.
Verified wiring
The reference ID's encoder-side drawing is D533387 for the 15-pin straight PCB connector. Follow the HEIDENHAIN drawing and its connector view for the numbered cavities. The manufacturer download routed to its maintenance notice during review. Obtain the drawing through the exact product record or HEIDENHAIN support before probing.
| Group | Function |
|---|---|
| Supply and sense | Encoder supply, return and corresponding remote-sense conductors. |
| Clock and data | Differential clock from the receiver and bidirectional EnDat data. |
| A/B analog tracks | Separate differential sine and cosine outputs. |
| Shield | Check the specified encoder housing and drive-side termination on the installed loom. |
Cables inside the motor and at the machine
HEIDENHAIN lists 606079-01 for the JAE 15-pin PCB connection to a 17-pin male M23 angle flange socket. It includes temperature-sensor leads. For an unstripped open end, see 605090-01 and 605090-02. Confirm the PCB socket, cable length and motor-side termination from the installed assembly.
Mitchell TI-5668 is the direct test lead documented for this encoder family. The MOOG article separately lists TI-5059 for the stated motor interface.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Drive sees the encoder but reports analog feedback loss | Compare A/B amplitude and quadrature at the encoder and receiver with the specified input termination. Inspect the corresponding harness pairs. |
| Absolute read fails but A/B activity remains | Check clock and data pairs, receiver configuration and the encoder supply under load. |
| Position is noisy once per revolution | Look for cyclic runout, contact marks or a shifted coupling before changing the drive feedback settings. |
| Position jumps after an encoder swap | Confirm the exact EnDat variant, direction, turn count and the original motor or machine reference. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Mitchell lists EQN 1125 as a MOOG feedback option. The exact MOOG motor order and 678096-20 installation are still to be matched. Use the motor label and fitted encoder label together. Compare the EQN 1325 guide for the separate larger-frame product.
Angle of alignment and commissioning
Verify the stator attachment and shaft seating first. For motor commutation or an axis datum, obtain the OEM procedure for the exact motor and drive. Read and preserve motor-specific encoder or drive data if the OEM supports it. Restore data only to the compatible replacement for that same motor and verify position and direction.
Drawings, pin maps and manuals
- Main technical PDF. HEIDENHAIN Encoders for Servo Drives, document 208922, ECN/EQN 1100 series. The exact-ID product record governs shaft and coupling.
- Manufacturer reference. Match the exact order code or the identified motor option.
- HEIDENHAIN Cables and Connectors, 1206103. EnDat01 JAE harnesses 605090-01, 605090-02 and 606079-01.
- Mitchell MOOG motors guide. See the EnDat options and direct-to-encoder cables.