What specialist testing can show
TI-5000JX bench. Verify EnDat communication and position. Use OEM procedures for any functional-safety evaluation.
TI-3000JX motor run. Confirm motor fit, drive support and any safety requirements with the exact motor order.
Starting lead. Match the fitted 12+4 PCB connector and approved EnDat22 connection.
HEIDENHAIN EQN 1337 / 1327453-04 Multiturn EnDat22 Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| 1327453-04 | EQN 1337 multiturn, 67M blind bore and 07B expanding-ring coupling. |
| 1327452-02 | ECN 1325 singleturn partner in the same 12.7 mm product sheet. |
| 1178027-01 | EQN 1337 multiturn with a 65B taper in product information 1378230. Compare mounting before sourcing. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Data | EnDat22 digital position. The OEM table gives 25 bits within one turn and 12 bits of turns for EQN 1337. |
| Supply | 3.6–14 V DC under the cited OEM conditions. |
| Fit | 67M 12.7 mm blind hollow shaft, axial clamp, 65 mm installation diameter and 07B expanding-ring coupling. |
| PCB connection | 16 contacts split 12+4. Temperature sensor connections use the separate group where fitted. |
Interface and measuring method
The drive reads absolute within-turn position and turn data over EnDat. HEIDENHAIN limits the safety-related position scope in this sheet to the singleturn range. Validate the machine’s safety function under the full OEM procedure.
Mounting and fit
Check the shaft, axial clamp and mating locating hole on the drawing for this ID. Confirm positive engagement and the specified fastener before assembly. The 65B taper drawing belongs to a different order.
Wiring and connector scope
Use the 12+4 connector view in the OEM PDF to identify supply and sense, clock, data and temperature. Keep PCB and motor bulkhead pin maps separate and verify the cable and drive before applying power.
Internal motor and machine cables
Document the factory harness between the PCB and motor connector. Confirm the separately routed temperature sensor pair where used. Obtain the fitted cable and exact HEIDENHAIN ID before purchasing a replacement.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Within-turn value valid, turn count unexpected | Confirm that the drive is configured for the exact EQN multiturn order. |
| Intermittent serial error after mechanical work | Check the plug lock and internal harness routing against the motor drawing. |
| Safety or reference fault after replacement | Check the full ID, rotor and coupling fit, reference and safety commissioning record. |
Angle of alignment and commissioning
Record the received direction and reference. Follow the drive and safety documentation to verify position and attachment after replacement. For machine safety functions, a readable position value is one part of commissioning.
Motor and drive applications
Servo motor with verified 1327453-04 order
Identify the 12.7 mm blind hollow shaft, order-specific connector and multiturn position format.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitchell Product Catalog, supported feedback. HEIDENHAIN supported EnDat feedback, EQN1337
- HEIDENHAIN ECN 1325 / EQN 1337 product information. Supplementary reference for the stated model or setup.
- HEIDENHAIN taper-shaft product information 1378230. Tapered EQN 1337 order 1178027-01 for mechanical comparison.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.