Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
With the approved load and supply, a qualified bench test can compare A/B phase, N, alarm and count through a known turn. Observe the same channels at the machine input to isolate a harness or receiver problem. Mitchell exact profile support is unverified.
Hengstler RI58-O 0552676 Push-Pull Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is RI58-O/ 1024EK.42KB-P0. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| RI58-O/ 1024EK.42KB-P0 / 0552676 | K.42 codes a 10 mm solid shaft, M3 clamping flange and IP65 family configuration. B codes a radial PVC cable. | 1,024 pulses/rev, E supply 10–30 V DC, K push-pull. Verify the exact P0 configuration with Hengstler. |
| RI58-O/ 1024EK.42KB / 0522462 | Same published core flange, shaft and cable codes. | Same published core count and output codes. The ordering table lists this as a separate part. |
| RI58 family, I or R output options | Check full type, mounting and connection codes. | I adds complementary push-pull outputs. R uses RS-422 with alarm. |
Production and end-of-life status
Hengstler lists item 0552676 as quote only in its exact product record. Request current orderability and production status for the complete P0 code.
Specifications
| Parameter | Value and scope |
|---|---|
| Resolution | 1,024 pulses per revolution, A/B quadrature and N reference. Receiver edge counting can produce 4,096 counts/rev. |
| Power / output | E code 10–30 V DC. K code push-pull, A/B/N plus alarm. 200 kHz family maximum pulse frequency for push-pull. |
| Fit / lead | K.42 clamping M3 flange, 10 mm shaft. B radial PVC cable. Select the actual mounting drawing. |
| Enclosure | K.42 catalogue IP65 configuration. Check the data sheet's shaft-entry qualification and the P0 configuration. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Measure the 10 mm shaft and read the clamping-flange drawing before selecting a coupling. Check the mating pilot, shaft engagement, coupling alignment and cable bend clearance. Use the correct fasteners and torque for the actual bracket and coupling. Check thrust and radial loads against the family conditions.
Interface and measuring method
A and B change state in quadrature as the shaft rotates. Their lead or lag gives direction. N is the index reference and the alarm line is separate. The K output drives both high and low with a common reference. Check the receiver's input ratings and threshold for the installed supply.
Verified wiring
Use the K column in the manufacturer's PVC cable A/B table. It applies to the B radial PVC lead when the original harness matches the exact order code. Identify each conductor by its colour and confirm any OEM splices.
| Function | Wire |
|---|---|
| Supply / return | Red / black |
| A / B / N | White / green / yellow |
| Alarm | Yellow with black tracer |
| Screen | Connected to encoder housing per datasheet |
Terminate the screen per the machine EMC drawing and account for its intended housing bond during isolated short checks.
Cables inside the motor and at the machine
The B code has a factory radial lead. Hengstler's accessories list 3 280 114 as 10-core screened PVC cable by length. Confirm that the selected cable and termination match the existing machine harness and output speed. For a repair splice, verify conductor mapping and screen continuity after both ends are disconnected.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| No counts in either direction | Check loaded supply, input mode and whether the coupling actually turns the encoder. |
| Direction changes randomly or count jumps | Compare A and B edges at both ends. Inspect cable routing and strain, input thresholds and coupling play. |
| Counts are fine but origin is lost | Check N at the controller and the homing logic. Check the alarm output independently. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Hengstler lists CNC axes, packaging machines, drives and other machinery for the RI58 family. Confirm the exact machine's input voltage, pulse rate, count mode and mounting.
Angle of alignment and commissioning
Align the coupling mechanically, establish count direction and verify index or machine home. Capture the existing PLC scaling and reference position before changing the encoder. Use the OEM commutation procedure if this encoder participates in a motor control system.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Electrical tables, PVC A/B cable. Use the K column.
- Clamping flange dimensions. Use the radial B drawing.
- Hengstler ordering information. Decodes E, K.42, K and B. Lists 0522462 as a separate match code.