Identify the fitted part
| Guide scope | Indramat MDD021 / MDD025 / MDD041 K — motor application |
|---|---|
| Feedback identity | RSF + IDG resolver/absolute assembly |
| Main model / application identifier | MDD021 |
| Motor order / source example | Obtain the complete fitted motor order; the family reference is not an inspected unit. |
| Interface | resolver with integrated absolute pulse-wire encoder |
| Starting connection | Exact MDD resolver fixture to verify; do not reuse a MKD/MKE internal lead by analogy |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX scope. Identify RSF + IDG K, retained multiturn position and the separate memory/resolver paths before removal. Confirm exact connector view, supply, fixture and installed tester software. |
|---|---|
| Starting lead / fixture | Exact MDD resolver fixture to verify; do not reuse a MKD/MKE internal lead by analogy |
| Profile / module | Confirm exact connector view, supply, fixture and installed tester software. |
| TI-3000JX motor-run scope | Do not run from the family table alone. Confirm exact MDD motor, resolver excitation, board connection and supported run profile. |
The documented test reference is Indramat Digital Motors, Serial Encoders and Resolvers — Mitchell Types Supported resolver MDD row; OEM Fig.2.17 and G/K order keys. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current production status, stock and a verified successor for the exact fitted order remain to confirm with the manufacturer. The linked reference establishes the stated technical scope, not stock or drop-in compatibility. Compare fit, voltage, interface, connector, motor data and alignment before ordering.
Specifications and interface
| Feedback technology | resolver with integrated absolute pulse-wire encoder |
|---|---|
| Motor frames | MDD021, MDD025, MDD041 |
| Feedback option | K: RSF plus IDG integrated pulse-wire absolute encoder. |
| Fit / service values | Exact shaft/coupling dimensions, pin map, tightening torque and service ID must match the fitted drawing; unverified values remain open. |
The resolver has an excitation winding and sine/cosine output paths. Confirm the actual excitation frequency/voltage, winding map, transformation ratio and pole count from the exact drawing. Check the analogue resolver and any independent memory/absolute retention path separately.
Mechanical fit and retention
Record the incoming shaft datum, locating seat, coupling, retaining cover, fasteners and cable exit before removal. After isolation, inspect accessible looseness, contamination, rubbing and bearing condition. Use the exact outline and service procedure for engagement, rear clearance and fastening. Do not import torque, air gap or coupling dimensions from a similar-looking motor.
For MDD021, MDD025 and MDD041, K combines RSF resolver feedback with the IDG integrated pulse-wire absolute encoder. Record both within-turn resolver behavior and retained revolution information. This distinguishes K from the G relative arrangement. Check the precise assembly and memory path before removal; a resolver-only measurement cannot verify the complete absolute system.
Wiring and connector boundaries
Separate the encoder plug, internal motor loom, bulkhead, machine cable and tester fixture. Verify contact numbering, keying, gender and drawing viewpoint. Identify supply/return, signal pairs, shield and independent temperature or brake paths from the exact diagram. Unverified pin assignments remain open.
Starting connection for this guide: Exact MDD resolver fixture to verify; do not reuse a MKD/MKE internal lead by analogy. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
The fitted internal loom part number is not established by the motor family or protocol. Record both ends and obtain the motor assembly drawing. Machine cable selection also depends on receiver, length, shielding and fixed/flexing duty. A Mitchell test lead is not an OEM replacement cable number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact assembly | For MDD021, MDD025 and MDD041, K combines RSF resolver feedback with the IDG integrated pulse-wire absolute encoder. Record both within-turn resolver behavior and retained revolution information. This distinguishes K from the G relative arrangement. Check the precise assembly and memory path before removal; a resolver-only measurement cannot verify the complete absolute system. |
|---|---|
| Intermittent fault with cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, moisture and old repairs. Check continuity and unintended shorts against the exact diagram, accounting for intentional shield bonds. |
| No communication or usable signal | Confirm the fitted feedback, supported fixture and supply range. A qualified technician can compare source and load voltage with the approved breakout and OEM procedure. Connector shape alone does not establish a safe pin map. |
| Position reads but drive rejects the feedback | Check independent signal paths, motor identity, direction, index/retention and mechanical attachment. Record the original alarm and readable data before changing settings. A reset cannot establish compatible motor data. |
| Resolver signals look normal but reference is wrong | Inspect the separate memory path and mechanical datum. For K, verify IDG revolution information; a resolver-only measurement does not test it. |
Alignment, reference and memory
Record the original mechanical reference, direction, motor phase convention, retained state and readable data before disturbing the feedback. Use the exact motor procedure for alignment and replacement. Electrical communication alone does not establish machine origin or correct motor/feedback pairing. Numerical alignment examples must stay with their stated motor, polarity and phase convention.
Motor and drive applications
MDD021 / MDD025 / MDD041 K. For MDD021, MDD025 and MDD041, K combines RSF resolver feedback with the IDG integrated pulse-wire absolute encoder. Record both within-turn resolver behavior and retained revolution information. This distinguishes K from the G relative arrangement. Check the precise assembly and memory path before removal; a resolver-only measurement cannot verify the complete absolute system.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Indramat Digital Motors, Serial Encoders and Resolvers — Mitchell Types Supported resolver MDD row; OEM Fig.2.17 and G/K order keys
- Indramat MDD digital AC servo motor project planning — Exact family, feedback option, connection drawing and revision only
Obtain the fitted motor and encoder labels, exact service ID, internal loom/contact-view drawing and approved fixture. Match the linked manufacturer document to the exact order and revision.
Common questions
What should accompany a MDD021 / MDD025 / MDD041 K enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Do not run from the family table alone. Confirm exact MDD motor, resolver excitation, board connection and supported run profile. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.