Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Check count per turn, differential levels, A/B phase and index in a suitable fixture and under the documented load. Compare signals at the controller to find a wiring or input problem. Exact Mitchell adapter support remains unverified.
JTEKT Koyo TRD-SH1024VD Differential Hollow-Shaft Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is TRD-SH1024VD. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| TRD-SH1024VD | Ø38 mm body, 8 mm hollow shaft, 2 m integral cable. | 1,024 pulses/rev, 5 V differential line driver, A/B/Z. |
| TRD-S1024VD | Separate solid-shaft model in the TRDV declaration. | 1,024 P/R VD line-driver variant. Verify shaft fit and installation drawing. |
| TRD-SH … AD or BD | Related hollow-shaft versions. | Different open-drain output and supply requirements. Use the AD or BD column. |
Production and end-of-life status
AutomationDirect lists the exact TRD-SH1024VD in its Retired Products catalogue. Confirm current JTEKT production or a supported successor with the manufacturer.
Specifications
| Parameter | Value and scope |
|---|---|
| Fit / lead | 38 mm body, 8 mm hollow bore, 2 m integral lead, IP40 in the exact cutsheet. |
| Power | 5 V nominal. VD diagram gives 4.75–5.25 V DC. |
| Output | Differential line-driver A/B/Z. 1,024 pulses per revolution. |
| Mechanical limits | Family installation sheet states up to 6,000 rpm and uses the lower frequency-derived or mechanical limit. Exact cutsheet lists 20 N radial and 10 N axial load. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Use the TRD-SH hollow-shaft diagram and mating shaft requirements. Check the 8 mm shaft fit, retaining arrangement, runout and bracket alignment. Keep the lead clear of the moving shaft. Follow the installation diagram for seating and fastening.
Interface and measuring method
The VD differential driver sends A/B quadrature and Z index. The receiving counter determines direction from the phase relation and can count one, two or four edges per cycle depending on its configuration. Set the receiver for the documented 5 V line-driver circuit.
Verified wiring
Use the VD line-driver connection drawing on the installation sheet. The following colours refer to the original encoder lead. Map them independently through any OEM plug.
| Function | Wire |
|---|---|
| +5 V / 0 V | Brown / blue |
| A+ / A− | Black / purple |
| B+ / B− | White / grey |
| Z+ / Z− | Orange / yellow |
| Screen | Follow the machine scheme. At 1,024 P/R the sheet shows no internal screen-to-housing bond. |
Cables inside the motor and at the machine
The exact cut sheet describes the integral 2 m lead. For an extension, use the suitable differential pairs, screen and supply conductors per the receiver and machine drawings. Keep away from motor and power cabling. Obtain the exact remote connector from the machine loom.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Missing all signals | Verify 4.75–5.25 V across brown/blue under approved conditions. Confirm the driven shaft and receiver mode. |
| Count runs in the wrong direction | Check A/B mapping and polarity from both ends, then confirm the PLC direction setting. |
| Noise or losses when a drive switches | Inspect routing, screen, pair integrity and the receiver differential termination. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use on compatible machine counters and drive inputs with an 8 mm mating shaft and a 5 V differential receiver. The related AD and BD output variants require their own circuit and supply check.
Angle of alignment and commissioning
Install the encoder in the documented mechanical orientation, verify count direction and re-establish machine zero via the approved homing procedure. The Z channel aids reference recovery. Use the OEM motor instructions if the machine also requires motor commutation setup.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- TRD-SH1024VD exact cut sheet. Confirms ID, body, bore, output and lead.
- Distributor retirement record. Use to distinguish distributor orderability from manufacturer lifecycle.
- TRDV declaration and model list. Lists the separate TRD-S1024VD solid-shaft model.