Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell documents an OSA105-family bench readout. Confirm the S2A label, protocol and connector, compatible profile and exact test harness before using TI-5000JX. The TI-3000JX motor-run selection requires separate verification.
Mitsubishi Electric OSA105S2A Servo Feedback Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is OSA105S2A. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| OSA105S2A | Full marking reported by suppliers. Confirm the actual label, shaft and installed motor drawing. | Mitsubishi documents OSA105-family high-speed serial. Exact S2A signal and connector scope pending. |
| OSA105 | Mitsubishi OEM family designation in MDS-C1-N documentation. | High-speed serial motor-end encoder in the compatibility table. |
| OSA105-ET | Separate entry in Mitsubishi's machine-end section. | Confirm installation role and supported drive, even where the family name is similar. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| OEM family interface | High-speed serial at the motor end for OSA105 in Mitsubishi IB(NA)1501296. The table is at family scope. |
| Readout convention | Mitchell distinguishes the OSA105 family’s serial count representation from how the drive or literature describes resolution. |
| Connection and limits | S2A-specific supply, connector view and pin assignment need the OEM motor or encoder drawing. |
| Drive identification | Record the exact MDS unit and supported feedback option before selecting the setup. |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Pair the original motor tag with the full encoder marking. Check the mounting pilot, shaft or coupling, axial retention and lead routing on the OEM assembly. Retain the reference and observe the installed position before moving the rotor. Use the exact manual for torque and fit limits.
Interface and measuring method
The documented OSA105 family sends position as a high-speed serial word. A drive can scale the data for its position display, so compare the actual receiver settings and the OEM definition of counts per turn. One supplier description calls the S2A incremental. Resolve the exact assembly from the motor drawing and use the Mitsubishi family table to guide that check.
Verified wiring
Mitsubishi serial fixtures exist with different data-pair and connector arrangements. Identify the complete motor and drive before mapping supply, return, serial connections and shield. Use the exact connector drawing rather than extrapolating pin numbers from OSA104, OSA18 or the OSA105-ET machine-end version.
Cables inside the motor and at the machine
The Mitchell cable index has several Mitsubishi serial leads differentiated by connector. Obtain the matching OEM feedback cable number from the motor and MDS unit. The product guide needs the S2A connector and wiring drawing before a Mitchell test lead or internal harness can be assigned.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| MDS reports feedback loss immediately | Record the drive alarm and exact model, verify the selected motor-end encoder type, then inspect and test the isolated harness. |
| Receiver count appears different from the catalogue | Compare the interface word, drive scaling and displayed units for the exact encoder family. |
| Fault started after substitution | Check the original suffix, motor-end versus machine-end role, installed lead and reference parameters. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare the documented supply or excitation under the specified load. Use the approved receiver or instrument to observe the appropriate data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
The MDS-C1-N compatibility table separates OSA105 motor-end from OSA105-ET machine-end roles. Establish the actual S2A motor and drive before applying the family table.
For a different Mitsubishi serial family, use the exact part and motor documentation. OSA18 technical guide.
Angle of alignment and commissioning
Save the original drive settings and available encoder identity and reference data under the OEM procedure before replacement. Verify mounting, motor commutation and machine datum separately. A supported readout of the serial word is one check in commissioning.
Drawings, pin maps and manuals
- Main technical PDF. Mitsubishi IB(NA)1501296. Section 1.1.4 gives OSA105-family drive compatibility. S2A-specific limits and mounting require the original assembly document.
- Mitchell Mitsubishi serial encoder guide. OSA105-family position readout and related serial types.
- Mitchell serial connection note. Application differences between two- and four-wire arrangements.
- Supplier S2A identification lead. Evidence of the observed suffix. Verify with the motor OEM before applying electrical or fit specifications.