Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
An approved RS-485 master can read registers, verify frame validity and exercise a controlled turn test. Read configuration first and write only as required by the machine procedure. Mitchell tester support for 2180528 is unverified.
POSITAL IXARC UCD-M200B Modbus RTU Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is UCD-M200B-1516-HFS0-PRM. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| UCD-M200B-1516-HFS0-PRM / 2180528 | 58 mm flange, 15 mm blind bore, 28 mm bore depth. Radial male M12. | RS-485 Modbus RTU, 15-bit turns and 16-bit angle. |
| UCD-M200B-1516-L120-PRM / 2180522 | 58 mm clamp flange with 12 mm solid shaft. | Modbus RTU. The mounting differs from HFS0. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Measuring system | Magnetic absolute position. The multiturn counter is powered by magnetic pulses and uses no gear or battery. |
| Output capacity | 16-bit singleturn and 15-bit multiturn. Check configured resolution and total measuring range. |
| Power / connector | 10–30 V DC. 5-pin male A-coded radial M12. |
| Mounting / speed | 58 mm flange, 15 mm bore × 28 mm depth. Maximum permissible mechanical speed 12,000 rpm. |
| Misalignment | Static axial ±0.3 mm and radial ±0.5 mm. Dynamic axial ±0.1 mm and radial ±0.2 mm for this item. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Measure shaft diameter and available insertion length before ordering the HFS0. Fit the encoder to the documented clamp and restraint arrangement. Compare actual shaft movement with the dynamic limits and check that the shaft has clearance at the blind end. Use the exact product drawing and instructions for clamping sequence and torque.
Interface and measuring method
The encoder is a Modbus RTU slave on an RS-485 line. The master polls the documented holding registers for position and other data. Verify device address, baud, parity, stop bits and how the PLC combines the position registers. The family manual lists factory defaults of address 127, 19,200 bit/s, even parity and one stop bit. Read the installed settings before relying on defaults.
Verified wiring
The manufacturer's Modbus RTU manual, section 4.1, identifies the 5-pin round connector contacts. Use the exact product's Connection Plan and molded pin numbers. Match the connector drawing and confirm the open-wire accessory colours independently.
| Pin | Function |
|---|---|
| 2 | Power supply + |
| 3 | Supply GND |
| 4 | RS-485 A+ per POSITAL |
| 5 | RS-485 B− per POSITAL |
| 1 | Signal GND |
Receiver A/B naming varies. Use the receiver's polarity definition and the manufacturer's termination and signal ground rules.
Cables inside the motor and at the machine
POSITAL lists POS-CBL-M12S-F05A-020DH-054N-000 as a 2 m PUR M12 A-coded female to open-wire accessory and 34050515 as the mating field connector. Confirm cable routing, bus length and remote-end pinout for the machine.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Slave times out | Check power, RS-485 polarity, address, baud, parity and end termination. Compare with a known-good slave or isolate a section under the site procedure. |
| Reads work but position is implausible | Verify register address base, multi-register parsing and scaling before touching the encoder mounting. |
| Position fails to follow the shaft | Inspect clamp and restraint. Compare raw count to measured travel, checking for slip or binding. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use on Modbus RTU PLC, gateway or position monitoring systems with the proper isolated serial interface. Confirm update rate and loss-of-communication handling for the application.
Angle of alignment and commissioning
Mechanical seating and torque restraint come first. Save address, framing, direction, scale and preset before replacement. Apply a new preset only at the machine reference and verify across the range. A servo commutation offset belongs to the motor's own feedback system.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Exact Connection Plan and Drawings tabs. The product record provides the item-specific flange, bore, connector and accessory information.
- POSITAL 2180522 comparison. Solid shaft version with the same Modbus RTU interface.