What specialist testing can show
TI-5000JX bench. Generic Incremental count and separate UVW display. Analog commutation output applies only to the documented variant.
TI-3000JX motor run. Exact motor-run setup open.
Starting lead. TI-5019Q or TI-5045Q for the documented branch
RENCO RCH20D 79994-004 ABZ and UVW Commutation Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| 79994-004 | Mitchell identifies this OEM part as RCH20D-2000/3-8MM-5/0-LD/VC-I-M6-S. Match the entire label. |
| RHS21D 79994-023 | Different OEM part. Mitchell documents ABZ without the 79994-004 commutation outputs. |
| F, H, N, S and Y | Electrocraft, Reliance and Allen-Bradley motor families cited by Mitchell. Confirm the fitted build rather than ordering by family alone. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Incremental resolution | 2,000 quadrature periods per revolution for the named unit. Mitchell shows 8,000 counts with four-edge decoding. |
| Commutation | UVW state outputs on the documented variant. The OEM branch can also have an analog step signal. |
| Test connections | TI-5019Q or TI-5045Q for the documented motor branch. Match the installed connector. |
Interface and measuring method
A/B phase supplies position and direction, Z supplies the reference, and UVW conveys commutation state. An otherwise clean A/B count does not prove the UVW pattern, order or phase relationship.
Mounting and fit
Compare the motor rear assembly and full encoder suffix. Check shaft engagement, axial seating, encoder body attachment and cable routing against the motor drawing. Preserve the incoming angular position before loosening the assembly.
Wiring and connector scope
Use the matching TI-5019Q or TI-5045Q cable sheet with the motor connector drawing. Identify position and commutation groups separately. The optional analog step signal is scoped to the matching OEM variant.
Internal motor and machine cables
The Q-suffix Mitchell leads are test adapters. Identify the original internal lead or machine cable from the motor order and connector view. Match its shielding and strain relief as well as the contact layout.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Good counts and poor commutation | Check all three commutation states, orientation and motor phase assignment. Inspect the encoder fixing before changing the drive. |
| One direction counts intermittently | Inspect the corresponding complementary pair and connector contacts. Check both channels and their phase relation. |
| Index missing with A/B present | Trace Z separately and compare the result with the correct variant and receiver. |
Angle of alignment and commissioning
Record the incoming UVW sequence, index behavior and mechanical position using the approved fixture. Verify the motor’s phase convention before alignment. Use the motor manufacturer’s procedure for the fitted encoder and pole configuration.
Motor and drive applications
Electrocraft / Reliance / Allen-Bradley F, H, N, S and Y
Compare the measured position and commutation signals. Confirm pin view and connector on the fitted motor.
Drawings, pin maps and manuals
- Renco Encoders. Allen Bradley / Reliance / Electrocraft. Exact 79994-004, application families and commutation.
- Mitchell pin and test cable references. Find the drawing for the exact Q-suffix fixture before using the pin map.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.