Site visit or send-in evaluation
We separate an ABSOSYN data or backup problem from an A/B count fault and inspect the 17-pin harness before replacing the encoder. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
For TI-5000JX, Mitchell documents the E07B151103 selection and comparing the serial position with the A/B count. For TI-3000JX, Mitchell documents the E07B15 four-pole selection for 61BM220BBAF0 using TI-5056. Confirm the exact motor, keyed harness, power connection and approved fixture before a run.
Sanyo Denki E07B151103 ABSOSYN Serial and Incremental Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is E07B151103. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| E07B151103 | Mitchell identifies it in 61BM220BBAF0. The mechanical drawing for the fitted unit is still needed. | 15-bit within-turn absolute position, bounded turn count and incremental A/B. TI-5056 is documented. |
| E07B151306 | Separate motor/encoder build. Verify the fitted code. | Different turn format and an incremental Z output in Mitchell's reference. |
| E10B171103 | Different motor example in the same legacy cable family. | Higher-resolution serial version. Select by exact label. |
Production and end-of-life status
The legacy application is documented by Mitchell. Confirm Sanyo Denki service availability and the exact encoder order before sourcing.
Specifications
| Parameter | Value and scope |
|---|---|
| Within-turn serial count | 15 bits, 32,768 positions per turn, per Mitchell |
| Serial turn count | Mitchell describes 0 through 1,799 revolutions for E07B151103. |
| Incremental track | A/B, 32,768 counts per turn in the documented setup. This variant has no Z channel. |
| Exact documented motor | 61BM220BBAF0 in the Mitchell Sanyo Denki run guide |
| Test harness | TI-5056, 17-pin MS according to the Mitchell index |
The table identifies the assembly each value applies to.
Mounting and fit
Confirm 61BM220BBAF0 and the encoder suffix before disturbing the mounting. With the load secured and isolated, record the as-found locating surfaces, retention, housing position and cable routing. Inspect for looseness, shaft play and wear on the mounting surfaces. Obtain the original service drawing for the exact fit and tightening specification.
Interface and measuring method
ABSOSYN serial data contains the within-turn count and turns. A separate incremental A/B channel reports movement. Mitchell uses the serial angle as a reference to compare A/B counts because this variant has no Z pulse. This helps distinguish a bad pulse channel from a lost serial response.
Verified wiring
Identify the 17-pin MS connector from the exact motor and the TI-5056 sheet. The serial pair, incremental tracks, operating supply and battery circuit must be traced individually. Use the published motor-side and tester-side drawings for cavity numbers and view. Supply and backup limits for the fitted unit need the OEM sheet.
Cables inside the motor and at the machine
Mitchell’s index names TI-5056 for E07B151103 and E10B171103, and the run guide cites it for 61BM220BBAF0. Identify the original motor's internal encoder lead and machine cable separately. Confirm the stamped key and bulkhead numbering before terminating any replacement.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Serial is stable but A/B disagrees | Verify the incremental pair path and counts using the documented serial reference. Account for direction and the full turn. |
| A/B responds but absolute read fails | Check serial pair continuity, receiver profile, loaded supply and connector condition. |
| Backup warning after long storage | Record the alarms and controller history. Mitchell describes a service reset for this exact encoder. Preserve any available reference and use the OEM backup and reset process. |
| Feedback shifts following motor repair | Check mounting, rotor reference and the exact motor’s phase arrangement. Confirm the drive’s settings. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Mitchell lists E07B151103 in Sanyo Denki 61BM220BBAF0. The other ABSOSYN models have separate data formats and motor combinations, even when the test cable is shared. Check the drive model and original motor ID.
Angle of alignment and commissioning
Capture the installed mechanical position and drive reference. Mitchell documents a specific TI-3000JX commissioning profile for 61BM220BBAF0. Use the OEM procedure and the exact motor phase and pole data to evaluate the commutation relationship. Preserve the original backup data before applying a reset.
Drawings, pin maps and manuals
- Mitchell Sanyo Denki bench guide. E07B151103 frame, A/B check and backup alarm notes.
- Mitchell Sanyo Denki motor run guide. E07B15 selection and documented 61BM220BBAF0 example.
- Mitchell manufacturer cable index. 17-pin TI-5056 cable reference.
These references describe the application and test route. The OEM encoder datasheet is still needed.