Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
With a compatible load and documented supply, a qualified technician can compare A/B phase and the Z marker across controlled turns. Check each complementary pair at both ends if the receiver misses edges.
Sensata BEI H25D 2000 PPR Complementary Incremental Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is H25D-SS-2000-ABZC-28/V-SM18. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| H25D-SS-2000-ABZC-28/V-SM18 | D square flange, SS shaft seal, side M18 connector. | 2000 ppr, A/B/index with complements, 28/V HTL driver. |
| H25D with 28/5 output | Check the same flange separately from the output option. | Regulated TTL output option in the ordering table. |
| H25D with EM18 | End connector changes installation clearance. | Use the documented M18 assignment and verify the mating face. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Mechanical | Square flange D with the standard ⅜ in shaft in the SM18 drawing. Confirm shaft and coupling details on the fitted unit. |
| Incremental tracks | 2000 ppr, A and B quadrature, Z reference and all three complements. |
| Power and driver | 28/V HTL supply range 4.75–30 V in the Gen 2 electrical table. Use the specified line receiver and operating conditions. |
| Connection | SM18 side 10-contact M18. Sensor-side letter assignments apply to the worked code. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Locate the square flange on its pilot and fit the correct flexible coupling to the shaft. Check coupling engagement, concentricity and clearance at the side connector. Compare the actual shaft option against the drawing before ordering a replacement.
Interface and measuring method
Two quadrature tracks report incremental motion and direction. Z supplies a once-per-revolution marker. The ABZC option adds complementary lines. Match the HTL level and choose the receiver's count convention before scaling speed or position.
Verified wiring
| Contacts | Function |
|---|---|
| D / F | Supply / circuit common |
| A / H | A / inverse A |
| B / I | B / inverse B |
| C / J | Z / inverse Z |
| G | Case |
Check the lettered contacts in the datasheet. Identify the machine-side shield termination from its drawing. The manufacturer shows different connector styles with different assignments.
Cables inside the motor and at the machine
Sensata lists M18 assemblies 31186-1810, 31186-1820 and 31186-1850 in 10, 20 and 50 ft. Match plug orientation and mating connector. For a custom cable, verify the isolated pin-to-pin path and the receiver termination.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| A count changes only in one direction | Check both A/B signal pairs and receiver direction decoding. |
| Machine loses home | Check Z at the encoder and receiver, then check the machine reference window. |
| Works at rest and drops out during motion | Check the coupling and cable flex, then compare frequency and input filtering. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use this worked order example for a driven or measured shaft with an HTL incremental receiver. Confirm the full configured label, any environmental option and the applicable approvals.
Angle of alignment and commissioning
Set the shaft coupling and flange within the installation limits. Preserve the original count direction and datum. Re-reference with the machine procedure if the marker is used for homing.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Gen 2 datasheet and order-code table. Use the H25D drawing, 28/V electrical row, M18 contacts and worked example.