What specialist testing can show
TI-5000JX bench. Resolver checks on the TI-5000JX using the approved excitation and the fitting TI-5908 plug setup or a documented terminal-board breakout.
TI-3000JX motor run. Verify the DFY order, polarity and matching drive fixture before any powered motor test.
Starting lead. TI-5908 on the Mitchell DFY resolver plug; terminal box requires its own verified breakout.
SEW-EURODRIVE DFY Resolver Motor Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| DFY71–DFY112 with terminal box | Use the terminal-board drawing and its marked circuit designations. Read the motor order and suffix from the plate. |
| DFY with resolver plug | Mitchell names TI-5908 for the illustrated resolver plug. Match the contact count and keying before connecting. |
| DFY absolute encoder option | A separate feedback branch is also illustrated. Use its own drawing and test method if that is what the motor order calls for. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback principle | Passive resolver with excitation, sine and cosine winding circuits. |
| Plug setup | 12-contact M23 on the illustrated TI-5908 branch. |
| Terminal-box setup | Use the motor-specific resolver terminal diagram. Preserve identification of thermal protection and feedback circuits. |
Interface and measuring method
The drive excites the resolver and derives electrical angle from its two return signals. A missing excitation path can make both returns disappear. A swapped pair can keep the angle reading smooth while changing its direction or phase.
Mounting and fit
Record the installed rotor position and the stator locating arrangement before disturbance. Use the complete DFY motor order and its rear assembly drawing for seating depth, fasteners and fit.
Wiring and connector scope
Open the DFY section of the linked Mitchell guide and select either its Resolver Connection drawing under Terminal Box or the separate drawing under Plug Connector. Compare the excitation and each return pair as a circuit. Keep the thermal pair and shield independent according to that view.
Internal motor and machine cables
TI-5908 is the test lead for the illustrated plug branch. Identify the terminal strip or factory pigtail from the exact motor order to source an internal harness. Obtain the installed cable drawing and connector keying for a machine-side replacement.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
A resolver is passive. Check isolated winding continuity against the matching drawing. Use the specified AC excitation on the approved test fixture for a signal check.
| Symptom | What to verify |
|---|---|
| Both sine and cosine returns are absent | Verify the excitation circuit, supply from the approved fixture and cable path before condemning the resolver. |
| Only one return drops out | Isolate the harness and measure continuity for the affected pair against the correct terminal or plug drawing. Inspect connector contact tension and contamination. |
| Angle tracks but the motor runs roughly | Check the fitted feedback option, winding polarity, resolver rotor fixing and commutation reference. |
Angle of alignment and commissioning
Preserve the original rotor-to-stator relationship. Use the matched SEW motor documentation and reference convention before a specialist measures alignment or restores operation.
Motor and drive applications
SEW DFY71–DFY112 terminal-box branch and documented DFY resolver plug branch
Confirm the exact terminal or plug branch, excitation and transformation ratio for the fitted motor.
Related SpareFaber guides
Drawings, pin maps and manuals
- SEW Servo Motors. DFY Series, resolver connections
- SEW DFY71–DFY112 terminal strip resolver drawing. OEM terminal-strip view reproduced in Mitchell’s DFY section.
- SEW DFY plug resolver drawing. Illustrated plug branch and view for the resolver and thermal circuits.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.