Identify the fitted part
| Guide scope | SEW-EURODRIVE CMP100L / EK1H — motor feedback application |
|---|---|
| Feedback identity | EK1H; fitted feedback label and connector to verify |
| Model / configuration identifier | CMP100L / EK1H |
| Motor order scope | Documented frame/feedback/brake configuration; not a complete winding, thermal-sensor or connector order |
| Interface | EK1H singleturn HIPERFACE + 1 Vpp |
| Starting connection | TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | TI-5000JX named CMP HIPERFACE evaluation and SEW memory support; actual profile, supply, connector and fixture must match the fitted unit. |
|---|---|
| Starting lead / fixture | TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps. |
| Profile / module | SEW motor-memory support; preserve electronic nameplate and check serial position and analogue tracks separately. Singleturn does not retain an absolute multi-revolution count. |
| TI-3000JX motor-run scope | Conditional on exact TI-3000JX motor/feedback profile, poles, phase order, alignment, power connection, restraint and amplifier envelope. No full-rating run capability is inferred from bench support. |
The documented test reference is SEW Servo Motors — Mitchell named CMP EK1H/AK1H synchronous absolute table; OEM drawing p.57, without brake; shown HIPERFACE extension 24 mm. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
The linked manufacturer document identifies this catalogue configuration. Current production, availability and any approved successor require confirmation against the complete fitted order. A downloadable manual does not prove present stock. Compare voltage, winding, mounting, shaft, brake, feedback, connector and stored motor-data requirements before accepting a replacement.
Specifications and interface
| Feedback technology | EK1H singleturn HIPERFACE + 1 Vpp |
|---|---|
| Frame / feedback / brake configuration | CMP100L / EK1H |
| Motor square flange | 163 mm |
| Motor shaft diameter | 32 mm; see drawing for tolerances |
| Overall axial length, including shaft | 434 mm; without brake |
| Brake scope | without brake |
| OEM outline reference | Printed page 57 of CMP catalogue 27799468/EN, November 2023 |
| Order scope | Frame, feedback and stated brake; complete winding, thermal-sensor and connector order not established |
| EK1H interface | Classic HIPERFACE singleturn with analogue sine/cosine tracks |
| Analogue periods per revolution | 1024; not the number of retained multiturn revolutions |
| Encoder supply reference | 7–12 V DC in the Mitchell EK1H/AK1H table; confirm the actual connection boundary |
| Mechanical feedback design | Conical-shaft motor feedback; exact assembly and retention remain to verify |
| Service values | Exact encoder coupling dimensions, pin map and tightening torque require the fitted assembly drawing. |
EK1H combines singleturn serial absolute information with 1024 analogue periods per revolution. Check serial communication, analogue sine/cosine quality and within-turn movement separately. EK1H does not retain an absolute multi-revolution count; do not describe it as AK1H multiturn feedback. This guide does not extend to HIPERFACE DSL or MOVILINK DDI. A mechanically close encoder with a different data profile is not established as interchangeable.
Mechanical fit and retention
Record the incoming shaft datum, pilot, bolt circle, rear clearance, cable exit and encoder retention before removal. Inspect play, debris, moisture and damaged contacts. Follow the exact assembly drawing for fits and fasteners; motor flange dimensions do not establish encoder coupling dimensions or tightening torque. Use the CMP100L outline on printed page 57. Its 163 mm flange and 32 mm shaft are independent dimensions. Verify pilot, bolt-circle, shaft projection, rear clearance and cable bend clearance from the same drawing. The EK1H housing adds the drawing’s 24 mm rear extension to the 410 mm outline length, giving 434 mm overall. Retain this clearance behind the motor.
CMP100L / EK1H identifies a 163 mm square flange, 32 mm shaft and 434 mm overall axial length including the shaft, without brake. This is a frame/feedback/brake configuration; winding, speed, thermal-sensor and connector suffixes still require the complete motor nameplate.
Wiring and connector boundaries
Keep motor power, protective earth, feedback and temperature circuits separate. Match contact numbering, keying, gender and mating-face versus wire-side view. Connector appearance alone is insufficient to establish a pin map. TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps. The named TI-5650 plus TI-5104 path applies to the matching 12-contact M23 motor feedback arrangement. A terminal box, a different motor plug or a direct encoder connection requires its own verified map. Assess serial communication and analogue sine/cosine tracks separately.
Starting connection for this guide: TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps.. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
Record the internal encoder-to-motor loom separately from the external machine cable and bench fixture. The internal loom part number is not established by the frame or interface alone. Obtain both connector faces, the assembly diagram and the correct contact view. Match cable length, shielding, temperature rating and fixed or flexing duty to the installation. A Mitchell test lead identifies a test connection; it is not an OEM replacement machine cable.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact configuration | CMP100L / EK1H identifies a 163 mm square flange, 32 mm shaft and 434 mm overall axial length including the shaft, without brake. This is a frame/feedback/brake configuration; winding, speed, thermal-sensor and connector suffixes still require the complete motor nameplate. |
|---|---|
| Intermittent fault during cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, contamination and earlier repairs. Compare continuity and unintended shorts against the correct diagram, accounting for intentional shield bonds. |
| Unstable position or missing feedback | Verify the actual sensor profile, matched excitation or DC supply, contact view and fixture. Inspect both analogue paths where applicable. A connector that mates mechanically can still have an incompatible pin assignment. |
| Position reads but the drive rejects it | Record the alarm, check the exact encoder identity and required motor data, then evaluate serial and analogue paths separately. A reset does not establish replacement compatibility. |
| Replacement dimensions look close | Compare this exact flange, shaft, feedback housing, brake and connector arrangement with the linked drawing. Do not use magnet-stack length, family digits or a similar power rating as the complete mounting envelope. |
Alignment, reference and memory
Preserve the original mechanical reference, phase convention, rotation direction and readable drive settings before disassembly. Communication or a smooth position reading alone does not prove correct electrical alignment or the machine reference. Preserve the original SEW motor-nameplate and model data before any supported memory operation. This data has a different purpose from the unique commutation offset stored in an Allen-Bradley MPL encoder. Mitchell’s common SEW +U/−V 60-electrical-degree and +U/−W 120-electrical-degree convention applies to most, not all, relevant motors. Match the fitted procedure, mechanical reference and software before using it; do not import an Allen-Bradley memory workflow.
Motor and drive applications
CMP100L; 163 mm square flange; shaft Ø32 mm; without brake. CMP100L / EK1H identifies a 163 mm square flange, 32 mm shaft and 434 mm overall axial length including the shaft, without brake. This is a frame/feedback/brake configuration; winding, speed, thermal-sensor and connector suffixes still require the complete motor nameplate.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- SEW Servo Motors — Mitchell named CMP EK1H/AK1H synchronous absolute table; OEM drawing p.57, without brake; shown HIPERFACE extension 24 mm
- SEW Standard Alignment — Named family and feedback option, rechecked 11 November 2026
- SEW-EURODRIVE CMP40–CMP112, 27799468/EN, November 2023 — 27799468/EN, November 2023; exact CMP100L / EK1H drawing, printed page 57. Axial length includes shaft.
- Batch 26 SEW CMP feedback and brake drawing cross-check — 27799468/EN 11/2023 pp.35,37,40,43,44,49,51,57,59,65,67; EK1H/AK1H table and named CMP resolver in Mitchell SEW article. Small-frame BK, medium BP, CMP112 BY. Exact motor order and brake rating remain to inspect.
Obtain complete fitted motor and feedback labels, exact service ID, internal loom and connector mating-face drawing. Confirm the linked document revision, fitted retention and enabled test setup before extending replacement, wiring or motor-run claims. SEW title is a frame/feedback/brake configuration; complete winding, thermal-sensor and connector suffixes remain to record.
Common questions
What should accompany a CMP100L / EK1H enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Conditional on exact TI-3000JX motor/feedback profile, poles, phase order, alignment, power connection, restraint and amplifier envelope. No full-rating run capability is inferred from bench support. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.