Identify the fitted part
| Guide scope | SEW-EURODRIVE CMP40M / RH1M — motor feedback application |
|---|---|
| Feedback identity | SEW RH1M resolver; verify fitted label and excitation |
| Model / configuration identifier | CMP40M / RH1M |
| Motor order scope | Frame/feedback configuration, standard motor without brake; not a complete winding order or inspected fitted unit |
| Interface | RH1M resolver |
| Starting connection | TI-5908 only for the matching 12-contact M23 resolver connection; verify winding pairs and connector view. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX named SEW CMP/CFM resolver evaluation, with actual excitation, ratio, connector and supported setup confirmed. |
|---|---|
| Starting lead / fixture | TI-5908 only for the matching 12-contact M23 resolver connection; verify winding pairs and connector view. |
| Profile / module | Confirm resolver excitation, ratio, winding pairs and fitted alignment. RH1M has no serial-encoder motor memory. |
| TI-3000JX motor-run scope | Motor-run scope remains conditional on the exact motor/feedback profile, poles, phase order, alignment, power wiring, restraint and amplifier envelope. Frame size or bench support does not establish full-rating run capability. |
The documented test reference is SEW Servo Motors — Named SEW CMP/CFM resolver family; OEM drawing p.35; standard no-brake configuration. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
The linked manufacturer document identifies this catalogue configuration. Current production, availability and any approved successor require confirmation against the complete fitted order. A downloadable manual does not prove present stock. Compare voltage, winding, mounting, shaft, brake, feedback, connector and stored motor-data requirements before accepting a replacement.
Specifications and interface
| Feedback technology | RH1M resolver |
|---|---|
| Frame / feedback configuration | CMP40M / RH1M |
| Motor square flange | 57 mm |
| Motor shaft diameter | 9 mm; see drawing for tolerances |
| Overall axial length, including shaft | 168.5 mm; standard no-brake configuration |
| Brake scope | Without holding brake; braked versions require their own outline |
| OEM outline reference | Printed page 35 of the linked CMP catalogue 27799468 |
| Order scope | Frame and feedback option; complete winding and connector order not established |
| RH1M sensor class | Two-pole resolver; one pole pair |
| Excitation reference | Mitchell table: 7 V AC nominal; verify fitted frequency, transformation ratio and supported setup before applying excitation |
| Motor-memory scope | No serial-encoder motor-memory read or copy operation for this resolver |
| Service values | Exact encoder coupling dimensions, pin map and tightening torque require the fitted assembly drawing. |
RH1M is a resolver, not a serial absolute encoder. Excitation and both analogue winding responses must be assessed together through a full mechanical revolution. A lost winding pair, poor contact, incorrect excitation or an altered phase relationship can each produce incorrect position. The two-pole designation describes the resolver; it does not establish the motor pole count. A resolver does not provide retained multiturn machine position.
Mechanical fit and retention
Record the incoming shaft datum, pilot, bolt circle, rear clearance, cable exit and encoder retention before removal. Inspect play, debris, moisture and damaged contacts. Follow the exact assembly drawing for fits and fasteners; motor flange dimensions do not establish encoder coupling dimensions or tightening torque. Use the CMP40M outline on printed page 35. Its 57 mm flange and 9 mm shaft are independent dimensions. Verify pilot, bolt-circle, shaft projection and cable bend clearance from the same drawing.
CMP40M / RH1M identifies a 57 mm square flange, 9 mm shaft and 168.5 mm overall axial length including the shaft in the standard no-brake drawing. This is a frame/feedback configuration; the winding, connector and any other fitted suffix still require the complete motor nameplate.
Wiring and connector boundaries
Keep motor power, protective earth, feedback and temperature circuits separate. Match contact numbering, keying, gender and mating-face versus wire-side view. Connector appearance alone is insufficient to establish a pin map. TI-5908 only for the matching 12-contact M23 resolver connection; verify winding pairs and connector view. Establish reference, sine and cosine winding pairs from the actual connection drawing. Check isolation and continuity with the assembly disconnected and the permitted measurement method. Supply frequency and transformation ratio must match the fitted resolver and selected tester setup.
Starting connection for this guide: TI-5908 only for the matching 12-contact M23 resolver connection; verify winding pairs and connector view.. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
Record the internal encoder-to-motor loom separately from the external machine cable and bench fixture. The internal loom part number is not established by the frame or interface alone. Obtain both connector faces, the assembly diagram and the correct contact view. Match cable length, shielding, temperature rating and fixed or flexing duty to the installation. A Mitchell test lead identifies a test connection; it is not an OEM replacement machine cable.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact configuration | CMP40M / RH1M identifies a 57 mm square flange, 9 mm shaft and 168.5 mm overall axial length including the shaft in the standard no-brake drawing. This is a frame/feedback configuration; the winding, connector and any other fitted suffix still require the complete motor nameplate. |
|---|---|
| Intermittent fault during cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, contamination and earlier repairs. Compare continuity and unintended shorts against the correct diagram, accounting for intentional shield bonds. |
| Unstable position or missing feedback | Verify the actual sensor profile, matched excitation or DC supply, contact view and fixture. Inspect both analogue paths where applicable. A connector that mates mechanically can still have an incompatible pin assignment. |
| Position reads but the drive rejects it | Check the resolver winding relationship, phase convention and exact motor profile. A serial-memory reset is not an RH1M diagnostic. |
| Replacement dimensions look close | Compare this exact flange, shaft, feedback housing, brake and connector arrangement with the linked drawing. Do not use magnet-stack length, family digits or a similar power rating as the complete mounting envelope. |
Alignment, reference and memory
Preserve the original mechanical reference, phase convention, rotation direction and readable drive settings before disassembly. Communication or a smooth position reading alone does not prove correct electrical alignment or the machine reference. Use the fitted SEW resolver procedure and exact motor profile. Mitchell describes a common SEW convention of +U/−V at 60 electrical degrees and +U/−W at 120 electrical degrees for most applicable motors; this is not a universal value. Confirm whether the actual motor follows that convention before alignment. RH1M has no serial memory from which to recover a motor-specific offset.
Motor and drive applications
CMP40M / RH1M; 57 mm square flange; Ø9 mm shaft; no brake. CMP40M / RH1M identifies a 57 mm square flange, 9 mm shaft and 168.5 mm overall axial length including the shaft in the standard no-brake drawing. This is a frame/feedback configuration; the winding, connector and any other fitted suffix still require the complete motor nameplate.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- SEW Servo Motors — Named SEW CMP/CFM resolver family; OEM drawing p.35; standard no-brake configuration
- SEW Standard Alignment — Named family and feedback option, rechecked 11 November 2026
- SEW-EURODRIVE CMP40–CMP112, 27799468/EN, November 2023 — RH1M resolver; pp.37,40,43 dimension drawings, standard motor without brake
Obtain complete fitted motor and feedback labels, exact service ID, internal loom and connector mating-face drawing. Confirm the linked document revision, fitted retention and enabled test setup before extending replacement, wiring or motor-run claims. SEW title is a frame/feedback configuration; complete winding and connector suffixes remain to record.
Common questions
What should accompany a CMP40M / RH1M enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Motor-run scope remains conditional on the exact motor/feedback profile, poles, phase order, alignment, power wiring, restraint and amplifier envelope. Frame size or bench support does not establish full-rating run capability. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.