Site visit or send-in evaluation
Share the feedback label, complete motor or machine order, drive model and alarm. Include both connector faces and note whether the issue followed a cable change, replacement or mechanical work.
What specialist testing can show
TI-5000JX bench. Mitchell describes a BiSS profile workaround for the named options.
TI-3000JX motor run. Exact motor run setup open
Siemens SIMOTICS S-1FL6 BiSS Servo Feedback technical reference
Find your part number
Use the full fitted label. A motor order identifies the assembly and should be recorded separately from an encoder part number.
| ID or order code | Identification and scope |
|---|---|
| 1FL6 L / M | Mitchell’s BiSS option families. Use the full motor order to distinguish singleturn and multiturn. |
| 1FL6 A | Incremental option. Its connector assignment and profile are separate. |
| Connector type 1 | Mitchell documents TI-5780 for the BiSS 15-pin D-sub connection. |
Production and end-of-life status
Confirm current orderability and any successor for the exact ID with the manufacturer or motor OEM. The dated documentation identifies the configuration.
Specifications
| Parameter | Verified scope |
|---|---|
| Absolute options | 21-bit singleturn or 20-bit singleturn plus 12-bit multiturn, depending on the build. |
| Documented supply | 5 V on the V90 X9 feedback connection. Verify the exact connector and drive type. |
| Signal path | Differential clock from the drive and differential data from the encoder. |
Mounting and fit
Record the motor order, frame size, inertia family and feedback plug. The V90 manual has different motor-side figures by shaft height and build. Use the exact assembly drawing before replacing the fitted encoder.
Interface and measuring method
The V90 receiver requests the absolute position with a clock pair and receives the result over the data pair. A healthy supply can coexist with missing clock, missing response or a data format mismatch.
Wiring and connector scope
The following map is the BiSS portion of the drive-side V90 X9 figure in the Siemens V90 PN operating instructions, section 4.5. Siemens shows separate motor-side figures. Use the applicable connector view and do not carry the drive-side numbering over to the motor.
| Contact | Documented signal |
|---|---|
| 1 / 2 | Data positive / negative |
| 4 / 3 | Clock positive / negative |
| 5 / 6 | 5 V supply |
| 7 / 8 | Supply return |
Cables inside the motor and at the machine
Mitchell’s TI-5780 applies to the documented Type 1 D-sub BiSS connection. The similar incremental motor uses another lead. Select an OEM feedback cable by the V90 and motor connector pairing.
Fault checks
Before inspection. Follow the site’s isolation and lockout procedure. Secure any load against movement, allow the specified discharge time and have a qualified technician verify isolation. Check resistance on a disconnected harness at both ends. Use the documented shield and return connections.
| Observation | What to verify |
|---|---|
| Drive has 5 V but position is unavailable | Check the documented clock and data paths with the correct receiver and wiring. |
| Link responds but the turn count is wrong | Confirm the exact singleturn/multiturn configuration and position word before re-referencing. |
| New plug looks right but the link fails | Identify the motor connector type, pin view and V90 cable family. |
Motor and drive applications
SIMOTICS S-1FL6. Full motor order open. Check the exact ID, drive and connector before applying an installation or test procedure.
Read the feedback and connector options before selecting a cable. Verify the exact word format and current software profile.
Angle of alignment and commissioning
Before disturbing feedback, record motor settings and machine reference. Confirm the encoder option and check OEM commissioning and zero procedures after service. A decoded position is only one part of the alignment check.
Drawings, pin maps and manuals
- Siemens 1FL6 feedback. General Information and Connection. L/M and Type 1 D-sub.
- Siemens V90 PN / S-1FL6 operating instructions. Section 4.5 shows X9 and separate motor-side pin maps by frame and option.