Identify the fitted part
| Guide scope | Siemens 1FT6 EnDat motor application — motor application |
|---|---|
| Feedback identity | ECN / EQN / ECI / EQI by complete fitted order |
| Main model / application identifier | 1FT6 EnDat motor application |
| Motor order / source example | Retain every nameplate suffix; a family example is not a verified fitted motor order. |
| Interface | HEIDENHAIN EnDat, exact option by order |
| Starting connection | TI-5031 only for matching Siemens EnDat motor connection |
| Configuration distinction | SY94 and TCG72/92 are component guides. This application adds the 1FT6 order and frame-specific mechanical/connection context. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX feedback scope. Decode the 1FT6 feedback option, frame, connector and analogue line count before replacement. Verify fitted feedback label, supply, connector view and installed tester profile. |
|---|---|
| Starting lead / fixture | TI-5031 only for matching Siemens EnDat motor connection |
| Profile / module | Verify fitted feedback label, supply, connector view and installed tester profile. |
| TI-3000JX motor-run scope | Conditional motor-run setup: verify exact motor, fitted feedback, poles, wiring, alignment, lead/module and installed TI-3000JX profile before running. |
The documented test reference is Siemens Motors — General Comments: 1FT6; supported EnDat profiles. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current availability, discontinuation and a verified successor for the exact fitted order remain to confirm with the manufacturer. The linked technical documents establish a scoped reference, not stock or drop-in interchangeability. Compare motor, drive, mechanical fit, interface, loom and memory requirements before ordering.
Specifications and interface
| Feedback technology | HEIDENHAIN EnDat, exact option by order |
|---|---|
| Profile boundary | Exact HEIDENHAIN model, period suffix, motor poles and installed support must match. Conventional EnDat/sine-cosine evidence does not cover DRIVE-CLiQ. |
| Module boundary | Where the documented TI-5101 motor-run connection applies, its switches are OPEN. Match the protected supply and cable to the actual sensor. |
| Exact fit and ratings | Use the matching manufacturer drawing for supply, connector view, shaft/coupling, dimensions and fastening. Unknown values remain open. |
Conventional EnDat and any analogue tracks must be assessed as separate paths. Preserve the exact encoder designation, period suffix and motor profile. Similar housing or ECN/EQN naming can occur with different interfaces. A plausible serial position does not confirm analogue quality, mechanical coupling or compatible motor memory.
Mechanical fit and retention
Record the incoming shaft datum, locating seat, coupling, retaining cover, fasteners and cable exit before removal. After isolation, inspect accessible looseness, contamination, rubbing and bearing condition. Use the exact outline and service procedure for engagement, rear clearance and fastening. Preserve the original relationship; do not import a torque or air gap from a similar-looking motor.
This guide concerns the 1FT6 motor fitted with conventional HEIDENHAIN EnDat feedback. Record the complete motor order, frame, encoder model, connector and analogue period suffix. The Siemens application profile must match the fitted encoder and motor pole count. Similar ECN/EQN family names can also occur with SSI or Indramat OEM formats; the name alone does not authorize an EnDat connection. DRIVE-CLiQ variants are outside this conventional-feedback scope.
Wiring and connector boundaries
Separate the encoder plug, internal motor loom, bulkhead, machine cable and tester fixture. Verify contact numbering, keying, gender and the drawing viewpoint. Identify supply/return, signal pairs, shield and any independent temperature or brake paths from the exact drawing. No unverified pin map is assigned in this guide.
Starting connection for this guide: TI-5031 only for matching Siemens EnDat motor connection. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
The exact fitted internal loom part number has not been verified. Record both ends and obtain the motor assembly drawing. Machine cable choice also depends on receiver, length, shield termination and fixed/flexing duty. A Mitchell test lead describes a bench connection and is not an OEM replacement cable number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact assembly | This guide concerns the 1FT6 motor fitted with conventional HEIDENHAIN EnDat feedback. Record the complete motor order, frame, encoder model, connector and analogue period suffix. The Siemens application profile must match the fitted encoder and motor pole count. Similar ECN/EQN family names can also occur with SSI or Indramat OEM formats; the name alone does not authorize an EnDat connection. DRIVE-CLiQ variants are outside this conventional-feedback scope. |
|---|---|
| Intermittent fault during cable motion | After isolation and disconnection at both ends, inspect flex points, pin engagement, moisture and repairs. Check continuity and unintended shorts against the exact diagram, accounting for intentional shield bonds. |
| No signal or communication | Confirm the encoder option, fixture and supply range. A qualified technician can compare source and load voltage using the approved breakout and manufacturer procedure. Connector shape alone is insufficient. |
| Position reads but the drive rejects feedback | Check independent signal paths, motor identity, direction and index/retention state. Record the original alarm and readable data before settings changes. A reset does not establish correct motor data. |
Alignment, reference and memory
Record the original mechanical reference, direction, motor phase convention, retained state and readable data before disturbing the feedback. Use the exact motor procedure for alignment and replacement. Electrical communication alone does not establish the machine origin or a correct motor/feedback pairing.
Motor and drive applications
1FT6 EnDat motor application. SY94 and TCG72/92 are component guides. This application adds the 1FT6 order and frame-specific mechanical/connection context.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Siemens Motors — General Comments: 1FT6; supported EnDat profiles
- Siemens 1FT6 configuration manual, October 2005 — Family-specific motor code, dimensions and connection tables; match fitted revision
Obtain the complete fitted motor order, encoder label, internal loom drawing, connector contact view and approved fixture. Match the linked family document to the actual order and revision.
Common questions
What should accompany a 1FT6 EnDat motor application enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Conditional motor-run setup: verify exact motor, fitted feedback, poles, wiring, alignment, lead/module and installed TI-3000JX profile before running. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.