Site visit or send-in evaluation
Network diagnosis, Mounting, Safety commissioning support. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
A suitable network bench can verify power, link and ordinary position. Safe position and speed require the correct safety controller, configuration and system validation. Confirm a specialist setup before any configuration write.
TR-Electronic CDV582M-19008 CIP Safety Multiturn Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is CDV582M-19008. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
Manufacturer device order code
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| CDV582M-19008 | Solid-shaft variant with ZB36 flange and radial connections. | EtherNet/IP with CIP Safety, FS03 in product record. |
| CDV582M family | Several flange, shaft and connector configurations exist. | Use the full item code and safety revision. A family label does not establish its network or safety option. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Resolution | 8,192 steps per revolution and 65,536 distinguishable turns for this order. |
| Supply and load | 10–30 V DC, dissipation below 3 W in exact record. |
| Shaft and flange | Solid shaft type 10N/M4/19.5, ZB36 with three M3 and three M4 positions. Use the drawing for fit and tolerance. |
| Connections | One four-pin A-coded male M12 for supply. Two four-pin D-coded female M12 for network. |
| Environment | IP65, −40 to +85 °C in exact record. |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Match the shaft and flange to 04-CDV582M-M0040. Check coupling condition, shaft engagement and strain relief with the axis isolated. Use the declared mounting limits for the safety encoder and coupler combination.
Interface and measuring method
EtherNet/IP carries standard information. CIP Safety adds a safety communication relationship with its own configuration and diagnostics. A valid ordinary position display can coexist with an invalid safe position.
Verified wiring
Separate the A-coded supply port from the D-coded Ethernet ports. Refer to TR-ECE-TI-DGB-0362 in the exact handbook before assigning contacts. Follow the drawing view, equipment bonding and connector instructions.
Cables inside the motor and at the machine
Select industrial Ethernet cordsets for the D-coded ports and the correct A-coded supply cordset. Record both cable ends and port labels. The handbook lists TR accessory options. The installed PLC and machine drawing govern exact cable selection.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Link or node absent | Check supply, keyed network connector, link indicators and the intended address before moving to safety diagnostics. |
| Ordinary position updates but safe position invalid | Record safety connection status, configured node and safety signature. Compare them with the approved controller project. |
| Position changes unexpectedly after replacement | Verify mechanical reference and compare scaling, direction and preset against the controlled configuration. |
Motor and drive applications
This exact CDV582M order fits a compatible EtherNet/IP/CIP Safety system. The handbook includes separate integration material for safety controllers. Verify device revision and the machine’s approved configuration.
Angle of alignment and commissioning
Record the mechanical reference and validated safety parameters before exchange. Recommission position and direction with the site safety procedure and document validation before returning the axis to production.
Drawings, pin maps and manuals
- Main technical PDF. Exact order handbook. See drawing 04-CDV582M-M0040, pin assignment TR-ECE-TI-DGB-0362 and CIP Safety documentation.
- Manufacturer reference. Match the exact order code or the identified motor option.