Identify the fitted part
| Guide scope | Yaskawa SGMPS serial feedback — Motor application |
|---|---|
| Feedback identity | Record the actual encoder label and complete motor order; the motor family is not a sensor part number. |
| MPN / full suffix | SGMPS serial feedback is the scoped designation. Retain all additional order characters and manufacturer IDs. |
| OEM service ID / motor order | Exact fitted-unit service number and motor order are not established; record them separately. |
| Interface | Yaskawa serial INC/ABS by motor code |
| Starting connection | TI-5762 / 5764 are series-level choices; match actual connector |
| Configuration distinction | No existing dedicated SGMPS motor guide. Existing Yaskawa device pages cover the encoder; this application adds motor-specific mounting, harness and identity checks. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | TI-5000JX serial count, turn-count, applicable commutation and alarm checks; manual profile selection. Mitchell cannot read motor/encoder memory, so preserve exact motor identity. |
|---|---|
| Starting lead / fixture | TI-5762 / 5764 are series-level choices; match actual connector |
| Profile / module | Match exact profile, supply, connector and installed software; named cable evidence is not a complete setup. |
| TI-3000JX motor-run scope | Unavailable: Mitchell Yaskawa Serial Encoder Testing explicitly says no run support. No TI-3000JX promise. |
The admission evidence is Yaskawa Serial Encoder Identification — Named motor list, Sigma III; fourth motor-order character identifies encoder. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current exact-order availability and an approved successor have not been confirmed. The linked technical references identify a configuration, not stock or universal replacement compatibility. Compare full labels, mechanics, interface, connector and motor data before ordering.
Specifications and interface
| Verified technical scope | Flat Sigma-III motor: verify frame-specific connector or flying-lead arrangement and 17-bit INC/ABS selection. |
|---|---|
| Selection boundary | SGMMJ: 13-bit INC / 17-bit ABS; SGMAS/SGMPS/SGMSS: 17-bit INC/ABS by actual motor code. The exact motor order determines availability. |
| Exact fitted order | Full suffix/ID, contact drawing, supply and receiver must match the actual assembly. Family specifications do not establish every unit. |
| Dimensions, fasteners and torque | Use the matching manufacturer drawing and revision. Unverified dimensions, air gap, torque and pin assignments remain open. |
Serial feedback must be selected by its actual protocol, code and returned identity. Record the incoming position, status and any supported revolution field before changes. Drive scaling, nominal encoder resolution and a tester menu designation are separate observations. A valid count does not establish mechanical fit, correct motor data or commutation.
Mechanical fit and retention
Photograph the incoming shaft reference, locating seat, restraint, fasteners and cable exit before removal. After isolation, inspect accessible looseness, contamination, bearing roughness and rubbing. The actual drawing determines whether the unit has integral bearings, a clamped shaft or motor-supported sensing. Do not force a sensing assembly or substitute a torque from a similar model.
Flat Sigma-III motor: verify frame-specific connector or flying-lead arrangement and 17-bit INC/ABS selection. No existing dedicated SGMPS motor guide. Existing Yaskawa device pages cover the encoder; this application adds motor-specific mounting, harness and identity checks. Read the fourth character after the five-character motor-family code to identify the fitted feedback option. The TI-5000JX profile is selected manually; an ID display of ---- is not automatic identification. Mitchell explicitly provides no encoder-memory reading and no TI-3000JX run support for these serial encoders.
Wiring and connector boundaries
Record the sensor plug, internal motor loom, motor bulkhead, external machine cable and drive/tester end as separate interfaces. Confirm gender, keying, contact numbering and mating-versus-termination view. Keep feedback, temperature, brake, motor power and shield contacts identified individually. A named test lead is not a pin map for an unverified adapter.
Starting connection for this guide: TI-5762 / 5764 are series-level choices; match actual connector. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
No internal OEM loom number or universal extension has been established for the exact fitted unit. Obtain its motor assembly drawing and both loom-end photographs. Select fixed or cable-carrier cable according to the actual installation, shielding and flex requirements. Mitchell lead numbers describe test fixtures and are not OEM replacement harness numbers.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Configuration to establish first | Flat Sigma-III motor: verify frame-specific connector or flying-lead arrangement and 17-bit INC/ABS selection. No existing dedicated SGMPS motor guide. Existing Yaskawa device pages cover the encoder; this application adds motor-specific mounting, harness and identity checks. Read the fourth character after the five-character motor-family code to identify the fitted feedback option. The TI-5000JX profile is selected manually; an ID display of ---- is not automatic identification. Mitchell explicitly provides no encoder-memory reading and no TI-3000JX run support for these serial encoders. |
|---|---|
| Intermittent fault when the cable moves | With power isolated and both cable ends disconnected, inspect flex points, repairs, engagement and contamination. Check continuity and unwanted shorts using the correct contact drawing, allowing for intentional shield bonds. |
| No signal or communication | Confirm the fitted order and approved fixture before a qualified technician measures the specified supply using the OEM procedure. Compare source and load at the appropriate breakout; a connector shell does not specify voltage. |
| Position moves but the drive still rejects feedback | Record identity, position, alarms and direction. Check the supported signal paths, retention and motor pairing separately; do not reset or overwrite data as a first diagnostic step. |
| Commutation or alarm indication differs from expectations | Use the manually selected Yaskawa profile. Applicable INC commutation checks exclude 24-bit INC; keep hand-rotation count, turn field and alarm observations separate. The test cannot validate unreadable motor memory or provide a motor-run result. |
Alignment, reference and memory
Mitchell cannot read Yaskawa serial encoder memory and does not support running these motors on TI-3000JX. Preserve the exact incoming motor/encoder pairing, key/reference position and drive records. Do not promise memory copying or infer a run profile from a successful count test. Any alignment or retention intervention must follow the exact OEM motor procedure with an appropriate specialist setup.
Motor and drive applications
SGMPS serial feedback. No existing dedicated SGMPS motor guide. Existing Yaskawa device pages cover the encoder; this application adds motor-specific mounting, harness and identity checks.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Yaskawa Serial Encoder Identification — Named motor list, Sigma III; fourth motor-order character identifies encoder
- Yaskawa Serial Encoder Testing — Named model, option or linked technical table
Exact fitted order, internal loom, contact view, fixture, supply and motor-specific setup remain to verify. Exact primary OEM PDF still to obtain. The previously located Sigma-III download no longer yields a readable PDF. Obtain SIEP S80000011D or the exact fitted-motor drawing; no broken download is presented as a verified PDF.
Common questions
What should accompany a SGMPS serial feedback enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Unavailable: Mitchell Yaskawa Serial Encoder Testing explicitly says no run support. No TI-3000JX promise. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.