Site visit or send-in evaluation
We can trace Sigma serial feedback through the machine cable and identify whether the fault follows the drive input, motor harness or encoder. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell documents 13-bit incremental serial testing on supported TI-5000JX Athena setups. Select the exact feedback type and compare position, status and applicable commutation display. Verify the harness and installed test option first. Confirm TI-3000JX run support for the complete motor and firmware separately.
Yaskawa UTSIH-B13 13-Bit Incremental Serial Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is UTSIH-B13. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| UTSIH-B13 | Mitchell identifies the encoder model and Sigma families. Read the whole motor code and fitted label for the exact assembly. | 13-bit incremental serial. Yaskawa's Sigma-II motor matrix lists feedback code A for SGMAH and SGMPH. |
| UTSIH-B16 | Different incremental serial option in supported Sigma models. | 16-bit selection. Confirm the motor and drive code before substituting. |
| UTSAH-B17 | Separate absolute serial family. Check the OEM motor configuration. | 17-bit absolute selection with separate turn retention requirements. |
Production and end-of-life status
Yaskawa maintains legacy Sigma-II application records. Ask Yaskawa for the exact UTSIH-B13 service order and supersession for the fitted motor.
Specifications
| Parameter | Value and scope |
|---|---|
| Encoder class | 13-bit incremental serial, 8,192 positions per turn |
| Motor option example | Code A in the documented Sigma-II SGMAH/SGMPH order matrix |
| Drive-side nominal supply | SGDH CN2 PG 5 V and PG 0 V per the manual |
| Signal path | SGDH CN2 PS and /PS carry encoder serial data |
| Motor cable example | Yaskawa JZSP-CMP00 family for applicable SGMAH and SGMPH motors |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Identify the exact motor and brake configuration before accessing the feedback assembly. With all motion and supplies isolated, document the shaft location, coupling and encoder housing attachment. Inspect for bearing play or movement after a motor repair. Use the OEM service drawing for the exact encoder fit and adjustment.
Interface and measuring method
The receiver exchanges position over Yaskawa's serial pair. The 13-bit incremental designation describes the motor feedback option. The position received by the drive is serial data. The drive's buffered pulse outputs to a host are a separate circuit.
Verified wiring
The table below applies to the SGDH Sigma-II SERVOPACK CN2 connector in Yaskawa section 3.5.2. Read the connector view and numbering in that drawing before back-probing through the approved test fixture. For the motor relay plug or encoder PCB, use the matching harness diagram.
| Pins | Function |
|---|---|
| 1 / 2 | PG +5 V / PG 0 V |
| 3 / 4 | Battery + / − for applicable absolute configurations |
| 5 / 6 | PS / inverse PS, encoder serial |
Confirm the fitted feedback option before wiring any backup circuit.
Cables inside the motor and at the machine
Yaskawa lists shielded JZSP-CMP00 cables for SGMAH and SGMPH. The wiring manual identifies JZSP-CMP9-1 and JZSP-CMP9-2 as the applicable mating plug/socket references for the specified connector arrangement. Match the motor suffix, connector and cable length. The internal lead is an OEM assembly item.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Drive reports encoder communication loss | Check SGDH CN2, loaded supply and PS pair. Confirm the exact motor and receiver type. |
| Wrong position step or count behaviour | Compare the 13-bit selection to the motor order code and read the serial diagnostics. |
| Intermittent fault during cable movement | Trace the relay connector and the disconnected encoder cable. Inspect contacts, screen and strain relief. |
| Fault starts after the encoder is disturbed | Check mechanical seating, orientation, the motor's reference and the OEM commissioning procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Mitchell identifies UTSIH-B13 in Sigma-II, III and V. Yaskawa documents the 13-bit option A on relevant SGMAH/SGMPH motors. Confirm the exact suffix and drive family. See the UTSAH-B17 guide for the separate absolute device.
Angle of alignment and commissioning
Record the original motor and drive data and the feedback reference before removing the encoder. Identify which values the OEM stores in the drive or encoder for the fitted option. Use the appropriate motor procedure and verify direction, commutation and datum after service.
Drawings, pin maps and manuals
- Main technical PDF. Yaskawa YEA-SIA-S800-32.2. Table 1.2 identifies feedback option A. Section 3.5.2 shows SGDH CN2 and section 5.8.1 describes the encoder cabling.
- Manufacturer reference. Yaskawa SGMAH Sigma II series. Compare the encoder identifier in the complete order code.
- Mitchell Yaskawa serial identification. Motor feedback letter and UTSIH-B13 model.
- Mitchell Yaskawa serial bench testing. Serial count and position checks.
- Yaskawa JZSP-CMP00 drawing record. Motor-side encoder cable drawing.