What specialist testing can show
TI-5000JX bench. Read the singleturn EnDat feedback at the encoder. Confirm the fitted device ID and retention of motor data.
TI-3000JX motor run. Verify a safe direct-feedback setup and motor data. Hybrid bulkhead run fixture remains open.
Starting lead. TI-5668 for the documented direct-encoder connection.
Festo EMMT-AS-80-M-HS-RSB Hybrid EnDat Singleturn Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| EMMT-AS-80-M-HS-RSB · 5255439 | Festo exact order, size 80 medium length, high-speed RSB configuration. |
| ECI 1118 | Festo lists this fitted rotor-position sensor for 5255439. Read its exact HEIDENHAIN ID for internal replacement. |
| RMB configurations | Other EMMT-AS orders use multiturn feedback. Read the complete motor order before transferring data or choosing the cable. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Rotor position | 18-bit singleturn, one absolute revolution, EnDat 2.2 on Festo 5255439. |
| Hybrid connection | M23x1, 15 contacts, motor-out code 80P. Festo lists digital motor-temperature transfer over EnDat 2.2. |
| Motor frame | Size 80, five pole pairs on the exact Festo order. Verify mechanical dimensions and flange in the catalogue. |
| Test connection | Mitchell specifies TI-5668 for direct encoder access on the EMMT-AS family. |
Interface and measuring method
The encoder provides serial absolute angle and the applicable status over EnDat. Festo also uses the digital path for motor temperature. A defect in the shared hybrid harness can affect several signals without a mechanical encoder failure.
Mounting and fit
Use the size-80 M-frame catalogue outline and installed ECI 1118 drawing. Record the rear assembly locating features, sensor seating and any gap reference before disturbing the inductive encoder.
Wiring and connector scope
Use the 80P hybrid connection drawing from Festo for the motor and drive. Use a separate, matching direct-encoder pin map for TI-5668. Confirm the contact view and keep power, feedback and any brake circuits distinct.
Internal motor and machine cables
Order the hybrid motor cable against 5255439 and the connected drive. Identify the internal harness by the fitted ECI connector. The TI-5668 fixture is a direct diagnostic connection.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Hybrid system faults but direct encoder reads | Inspect the shared cable, bulkhead, drive and cable routing with the 80P drawing. |
| Serial reading or temperature data drops out | Verify the exact EnDat path, connection and configured drive interface. |
| Fault begins after encoder replacement | Review the sensor installation, original memory and the motor-specific alignment record. |
Angle of alignment and commissioning
Preserve the original Festo memory and measured reference where supported. Verify the complete Festo commissioning procedure and the fitted EnDat service settings before fitting or programming a replacement.
Motor and drive applications
Festo EMMT-AS size 80, RSB
Use RSB and frame size to choose the right singleturn drawing and plan access behind the hybrid connector.
Related SpareFaber guides
Drawings, pin maps and manuals
- FESTO EMME-AS, EMMS-AS and EMMT-AS Series. EMMT-AS, size 60–80 encoder options, hybrid connector and TI-5668
- Festo EMMT-AS motor catalogue. Frame outline and ordering options for the exact RSB branch.
- Festo 5255439 exact motor data sheet. Fitted ECI 1118, 18-bit singleturn EnDat 2.2, hybrid interface and electrical/mechanical scope.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.