What specialist testing can show
TI-5000JX bench. Use the ECN413 selection and read the motor memory before planning replacement.
TI-3000JX motor run. Indramat run selection covers the listed ECN413 motor configurations. Confirm poles, wiring and readable memory.
Starting lead. Choose the Indramat lead from the fitted connector drawing. Module TI-5104 on the verified Indramat setup.
HEIDENHAIN ECN 413 Indramat Singleturn Digital Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| ECN 413 | Mitchell lists the Indramat singleturn ECN 413 among fitted feedback types on MDD and MHD motors. Record the complete encoder and motor orders. |
| DSF or HSF with SN and -H | Mitchell uses SN for singleturn and -H for HEIDENHAIN in this identification scheme. Match the entire marking. |
| ECN 212 and EQN 425 | ECN 212 is an earlier singleturn selection. EQN 425 includes a turn field. Their count and motor-memory configurations must be checked separately. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Measurement | Absolute within one turn on the documented ECN 413 selection. |
| Bench count | Mitchell groups ECN 413 with the 2,048 incremental counts per revolution selections. This is the tester count convention. |
| Stored data | Indramat motor identification and parameters. Preserve the original read before an exchange. |
| Motor scope | MDD and MHD each have other fitted encoder choices. Verify the DSF or HSF label. |
Interface and measuring method
The drive reads OEM digital position and motor information. Within-turn absolute position, incremental behavior and stored motor data provide different evidence during a diagnosis.
Mounting and fit
Obtain the outline and rear assembly reference from the full MDD or MHD motor order. Record the centering seat, shaft engagement, original fastener arrangement and cable routing before disturbing the encoder. Check the fitted ECN 413 drawing for internal fit.
Wiring and connector scope
Choose the documented Indramat connector and TI-5104 fixture by the motor label. Confirm the signal drawing and connector view on both ends. Keep the OEM digital feedback path separate from the motor power and brake circuits.
Internal motor and machine cables
Identify the motor-to-drive feedback cable by both complete orders. For an internal harness, use the fitted rear assembly and both plug views. The Mitchell fixture is for diagnosis at its documented connection.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Position reads but the drive reports a motor mismatch | Compare the DSF or HSF identity and the decoded motor memory with the motor label. |
| No serial reply | Check the fitted connector, cable and TI-5104 arrangement before judging the encoder. |
| Position repeatability changed after rear-end service | Check the centering seat, coupling or fastener reference and compare the incoming alignment record. |
Angle of alignment and commissioning
Capture the original motor data and incoming commutation reference. Compare the saved values to the motor nameplate. Use the applicable motor and encoder procedure to verify the mechanical reference and memory after fitting.
Motor and drive applications
Indramat MDD / MHD with fitted ECN 413
Distinguish the ECN 413 singleturn reading and motor memory from the EQN 425 multiturn setup.
Related SpareFaber guides
Drawings, pin maps and manuals
- Indramat Digital Motors, Serial Encoders and Resolvers. Types Supported and Data Display, ECN413 singleturn selection
- Indramat Motors. Supplementary reference for the stated model or setup.
- Bosch Rexroth MHD project planning manual. Manufacturer-authored motor feedback options, dimensions and electrical connections for MHD.
- Mitchell Indramat supported types. Legacy Indramat encoder identification and setup table.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.