What specialist testing can show
TI-5000JX bench. Check exact prefix and reported detector ID. Compare the bench count representation with the MELDAS scale.
TI-3000JX motor run. Mitchell lists P4 and P8 OSA104/105 for the supported legacy cases. Confirm motor poles and fitted detector.
Starting lead. TI-5008 on the documented legacy Mitsubishi arrangement.
Mitsubishi Electric OSA104 / OSE104 Legacy Serial Encoders technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| OSA104 | Absolute detector designation in the legacy 104 family. Verify the reported ID and the machine’s retention configuration. |
| OSE104 | Incremental detector designation using the legacy serial connection. Check how the drive establishes its machine reference. |
| OSA/OSE105 or 253 | Other legacy detectors. A shared connector or tester family does not establish the same drive resolution. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Bench reporting | Mitchell reports 1,048,576 positions per revolution for the 20-bit legacy tester representation. |
| Drive scale | The Mitchell article describes the 104 designation as associated with 100,000 counts. Confirm the scale and parameters in the actual MELDAS controller. |
| Wiring scope | Mitsubishi’s MDS-B-SVJ2 manual shows common connection diagrams for the 104 and 253 detector options on named motors. |
Interface and measuring method
The detector uses Mitsubishi request and reply circuits. The controller can identify the type from encoder data. A value that changes normally can still be scaled incorrectly if the selected type or drive parameters disagree with the fitted detector.
Mounting and fit
Mitchell describes removable OSA/OSE assemblies using a shaft coupling. Confirm the fitted 104 motor’s rear drawing, screw pattern, coupling condition and mating dimensions. Keep the original coupling orientation and mechanical reference.
Wiring and connector scope
Use the MDS-B-SVJ2 manual Chapter 2 diagram for the exact motor. It shows supply and return and the MR/MRR request and MD/MDR reply where applicable. Verify thermal and battery connections on the fitted assembly. Use TI-5008 only on its documented connection.
Internal motor and machine cables
Use the Mitsubishi motor and amplifier model to select the OEM cable drawing. Check the encoder pigtail and any thermal or retention branches separately. Match the fitted detector connector before testing through TI-5008.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Bench count and drive count differ | Compare the two count conventions and read back the actual detector ID before changing a parameter. |
| No serial reply | Verify the connector, supply, request and reply paths against the fitted motor diagram. |
| Reference changes after a detector swap | Check the retained-position arrangement, selected detector type and the coupling reference. |
Angle of alignment and commissioning
Record the original coupling position, drive setup and axis reference. Verify position direction, scaling and reference behavior with the actual motor and CNC procedure before operation.
Motor and drive applications
MELDAS motor fitted with the 104 detector option
Separate OSA104 absolute and OSE104 incremental at the OEM drive, and verify the correct count setting.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitsubishi Motors and Serial Encoders. Types Supported, OSA/OSE104 row and legacy count explanation
- Mitsubishi MELDAS MDS-B-SVJ2 manual. Chapter 2, detector wiring for the named HC and HA motor examples, including 104 and 253 variants.
- Mitsubishi Motors. Reference for the fitted feedback or motor option.
- Mitchell TI-5000JX legacy profile update. The software update renames the legacy profile for OSE/OSA 104/105/253.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.