What specialist testing can show
TI-5000JX bench. TI-5000JX Tamagawa manual lists the TS5668 family. Confirm the N26 connector and supported profile.
TI-3000JX motor run. TS5668N26 is listed under Generic Tamagawa V3.1. Complete motor-specific setup first.
Starting lead. Verify the TS5668N26 fitted connector before choosing a direct fixture.
Tamagawa Seiki TS5668N26 SmartABS Serial Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| TS5668N26 | Exact model listed under Mitchell Generic Tamagawa V3.1. Check the full fitted label. |
| TS5668 | Family reference in the TI-5000JX manual. Use the observed encoder ID and matching connector to select the bench profile. |
| TS5667 / TS5669N221 | Other SmartABS models with separately documented identities. Confirm the physical package and count scale for any replacement. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Interface | Serial SmartABS in the TS5668 family, with SD and its complement in the bench description. |
| Supply and retention | The Mitchell family description lists +5 V, 0 V and separate battery circuits. Confirm the N26 connector and approved supply before connection. |
| Position scale | Read the N26 device and verify the applicable document or reported count. The separately published TS5667 count belongs to that model. |
| Run software | TS5668N26 is named in the Generic Tamagawa V3.1 list. |
Interface and measuring method
The receiver gets position and status over the serial pair. The TS5668 family description has no separate A/B/Z output. Check communication, turn retention and reported device identity independently.
Mounting and fit
Record the N26 label, locating shoulder or coupling, connector latch and cable exit. Get the exact installed outline and motor drawing to verify fit before swapping a similar SmartABS unit.
Wiring and connector scope
Identify the approved serial fixture and matching supply and battery circuit from the fitted connector. Confirm the connector view and board revision. Use the OEM battery service procedure before disconnecting any retention path.
Internal motor and machine cables
Get the machine feedback harness by motor and drive order, then match the internal cable or pigtail to the N26 connector. Preserve shielding and the documented battery return.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Serial readout absent | Confirm the N26 label, fitted cable, supply and software profile. |
| Turns lost after shutdown | Verify the documented retention circuit and preserve the machine reference before battery work. |
| Angle runs with the wrong scale | Compare the actual device ID and count per mechanical turn with the matched profile. |
Angle of alignment and commissioning
Capture incoming absolute reference and any applicable stored data before removal. Use the motor and drive commissioning procedure to verify direction, retained position and commutation after service.
Motor and drive applications
Generic Tamagawa supported motor setups
Match the N26 suffix and check the retained-position behavior before comparing TS5667 or TS5669.
Related SpareFaber guides
Drawings, pin maps and manuals
- Generic Tamagawa Feedback Selection. Generic Tamagawa V3.1 supported encoder list, TS5668N26
- Tamagawa Serial Encoders. Supplementary reference for the stated model or setup.
- Mitchell Tamagawa supported-types chart. Compare separate SmartABS identities and use the documented lead for the fitted model.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.